747961

Futaba R7014SB Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
)87$%$&25325$7,21
<DEXWVXND&KRVHLPXUD&KRVHLJXQ&KLEDNHQ-DSDQ
3KRQH)DFVLPLOH
©FUTABA CORPORATION 2017, 2 (2)
All product and company names mentioned
herein are the trademarks or registered
trademarks of their respective owners.
*Fixed at neutral if a servo is connected to a port other than a usable transmitter channel.
*The telemetry and Extra Voltage ports cannot be used with the FASST system.
 
.
Turn on the receiver.
（
Transmitter OFF
）
.
Press and hold the Link/Mode button for at least 5 seconds.
.
When the link LED begins to blink green/red the button may be released.
.
The link LED should now be blinking red in one of the patterns described by the
chart below. ( Default : FASSTest )
.
Each press of the Mode/Link button advances the receiver to the next mode.
.
When you reach the mode that you wish to operate in, press and hold the Mode/
Link button for more than 2 seconds.
.
Once locked into the correct mode the link LED will change to a solid color.
.
Please cycle the receiver(s) power off and back on again after changing the
Channel Mode.
Link LED Red blink System
 FASSTest
 FASST Multi-ch Normal mode
3 FASST Multi-ch High-speed mode
 
.
Turn on the receiver.
（
Transmitter OFF
）
.
Press and hold the Link/Mode button for at least 15 seconds.
.
When the link LED begins to blink red the button may be released.
.
The link LED should now be blinking red in one of the patterns described by the
chart below. ( Default : S.BUS )
.
Each press of the Mode/Link button advances the receiver to the next mode.
.
When you reach the mode that you wish to operate in, press and hold the Mode/
Link button for more than 2 seconds.
.
Once locked into the correct mode the link LED will change to a solid color.
.
Please cycle the receiver(s) power off and back on again after changing the
Channel Mode.
Link LED Red blink System
 S.BUS
 DG2
FASSTest

FASSTest is a bidirectional communication system between the R7014SB receiver and FASSTest capable transmitters. Multiple optional telemetry sensors
may be connected to the S.BUS2 on the receiver and that data is in turn displayed on the transmitter.
*Please see your transmitter's operation manual to configure transmitter to operate with telemetry sensors.

Bring the transmitter and the receiver close to each other, within 20 inches (half
meter).
Turn on the transmitter. Place the transmitter into the receiver linking mode.
Turn on the receiver.
The receiver will wait for the linking process to begin for 2 seconds. Following
that it will return to the normal operation mode.
When the link LED of the receiver changes from blinking red to solid green,
linking is complete. (A link waiting state is ended in 1 second.)
• Refer to the transmitter's operation manual for complete details on how to place the
transmitter into the linking mode.
• If there are many FASSTest systems turned on in close proximity, your receiver might have
difficulty establishing a link to your transmitter. This is a rare occurrence. However, should
another FASSTest transmitter/receiver be linking at the same time, your receiver could link
to the wrong transmitter. This is very dangerous if you do not notice this situation. In order
to avoid the problem,we strongly recommend you to double check whether your receiver is
really under control by your transmitter.
• If the System Type of the transmitter is changed, the receiver will need to be re-linked to the
transmitter
.

S.BUS2 extends S.BUS and supports bidirectional communication. Sensors
are connected to the S.BUS2 port.
*Only S.BUS2 capable devices may be connected to the S.BUS2 port. Standard S.BUS servos
and gyros should not be connected to the S.BUS2 port.

It connects with the battery for power, etc.
$QRSWLRQDOH[WHUQDOYROWDJHLQSXWFDEOH&$59,1LV XVHG7KH
voltage of the battery can be displayed with a transmitter.

When using a TMA-1 (sold separately), change the settings by the following
method.
The TMA-1 is a device for viewing the telemetry data on a smartphone or
tablet.

.
Switch the receiver to FASSTest system.
.
Link the transmitter and receiver, and after confirming operation, turn off the
power.
.
Turn on the receiver power. (Transmitter power off)
.
Press the Link/Mode switch for at least 10 seconds.
.
When the link LED begins to blink green the button may be released.
.
The receiver enters the linked with TMA-1 mode, and the LED
simultaneously begins to rapidly blink red and green.
.
Press the TMA-1 link switch until the LED starts to blink and wait for the
TMA-1 to link.
.
When TMA-1 linking is complete, the TMA-1 LED changes from red to green
for a moment.
.
When linking is complete, turn on the receiver power and check the
operation of all the devices.

Bring the transmitter and the receiver close to each other, within 20 inches (half
meter).
Turn on the transmitter and receiver.
Link operation is performed by the Link/Mode switch.
• When using TM-8 module, it's possible to set F/S position (only 3CH).
0 to 1 sec. 1 to 2 sec. More than 2 sec.
0 sec. 1 sec. 2 sec.
Press and Hold time
No function
With TM-8
(not included in this set)
To set the F/S
position(No re-link)
Re-link(ID set) and to
set the F/S position
No function
Besides TM-8
Re-link(ID set)
*
Refer to the instruction manual of the transmitter or module used for a description of the
linking operation, F/S position setting methods and other details.

The MPDX-1 can be used with FASSTest by merely setting the corresponding
transmitter. (Refer to the instruction manual of the corresponding transmitter.) When
using the MPDX-10XOWL3URS'HFRGHUVROGVHSDUDWHO\ZLWKWKHFASST system,
change the setting by the following method. Enable the MPDX-1 at channels 11 and
12. (Initial value: OFF) Channels 11 and 12 cannot be used individually for MPDX-

.
Switch the receiver to the FASST system (Normal or High-speed).
.
Turn on the receiver power. (Transmitter power off)
.
Press the Link/Mode switch for at least 10 seconds.
.
When the link LED begins to blink green the button may be released.
.
The receiver enters the multi prop mode and the LED of the current mode
blinks. (Initial value: OFF)
.
Each time the switch is pressed, the mode changes.
.
When the receiver was switched to the desired mode, press the Link/Mode
switch for at least 2 seconds.
.
When the link LED begins to rapidly blink red and green, mode switching is
complete. Release the switch.
.
When switching is complete, turn on the power. When the power is turned
on, the receiver switches to the new mode.

When switched, the R7014SB can use the FASST-Multi-ch mode. When the FASST system is used, the telemetry and Extra Voltage ports cannot be used. The
FASSTV\VWHPKDVD1RUPDOPRGHDQGD+LJKVSHHGPRGH+RZHYHULQWKH+LJKVSHHGPRGHDQDORJVHUYRVFDQQRWEHXVHGDW&+
-
6.
Link LED Green blink Mode
1 time
Multi prop mode OFF
2 time
Multi prop mode ON
FASST
1 output.The MPDX-1 H[WHQGVFKDQQHOWR FKDQQHOV +RZHYHUVLQFH WKHUHVSRQVH
speed becomes slower and there are functional restrictions, use it at simple switch
operation and other applications that require numerous channels.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba R7014SB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba R7014SB in the language / languages: English as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info