747958
2
Zoom out
Zoom in
Previous page
1/2
Next page
WARNING
Do not perform the linking procedure while the motor's main wire connected
or the engine is operating as it may result in serious injury.
When the linking is complete, please cycle the receiver power and ensure
the receiver is properly linked to the transmitter.
Please power up your system in this order. Transmitter first, followed by the
receiver.
If the R7003SB receiver was previously linked to another transmitter, make
sure that transmitter is not operating while linking the receiver to the new
transmitter.
WARNING
Don't touch wiring.
* There is a danger of receiving an electric shock.
Don't connect to Extra Voltage before turning on a receiver.
When not using EXT-VOL, "EXT-VOL Mode" is turned OFF.
Don't connect EXT-VOL CABLE other than port 2 of R7003SB.
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
Link to the transmitter
Easy Link ID allows FASSTest receivers to link to compatible transmitter without pressing
the link button on the receiver.
1
Bring the transmitter and the receiver close to each other, within 20 inches (half
meter).
2
Turn on the transmitter. Place the transmitter into the receiver linking mode.
3
Turn on the receiver.
4
When the LED of the receiver changes from blinking red to solid green, linking
is complete.
* Refer to the transmitters operation manual for complete details on how to place the transmitter into the
linking mode.
* If there are many FASSTest systems turned on in close proximity, your receiver might have difficulty
establishing a link to your transmitter. This is a rare occurrence. However, should another FASSTest
transmitter/receiver be linking at the same time, your receiver could link to the wrong transmitter. This is
very dangerous if you do not notice this situation. In order to avoid the problem,we strongly recommend
you to double check whether your receiver is really under control by your transmitter.
* If the System Type of the transmitter is changed, the receiver will need to be re-linked to the transmitter.
* Link is required when a new model is made from a model selection.
How to change R7003SB into "EXT-VOL Mode" >
1
Turn on the receiver. LED lights up red.
[Transmitter is always OFF]
2
Press and hold the Mode/Link button for 5 seconds to 10 seconds.
*It becomes the mode which makes a mistake in exceeding 10 seconds. In that case, carry out power
supply OFF and redo.
3
The LED should now be early blinking green. Mode/Link button is released.
4
Each press of the Mode/Link button advances the receiver to the next mode.
5
When you reach the mode that you wish to operate in, press and hold the Mode/
Link button for more than 2 seconds.
6
When LED blinks in green with red, it is the completion of a mode change.
7
Please cycle the receiver power off and back on again after changing the EXT-
VOL Mode.
Mode
External voltage
measurement
LED blink
Servo Mode(Default)
OFF Green 1 time
EXT-VOL Mode
ON Green 2 time
Measurement of Extra Voltag
R7003SB can display the voltage of a receiver battery on a transmitter.
Furthermore, the following procedures are required in order to display the voltage of
another battery (Drive battery etc.).
1
The optional adapter for CA-RVIN-700 is purchased.
2
R7003SB is changed into "EXT-VOL Mode" in the following procedure.
*If "EXT-VOL Mode" is used, the port 2 cannot be used as the servo CH.
3
According to the manual of CA-RVIN-700, battery wiring is branched and it
connects.
4
One side of EXT-VOL CABLE is connected to the port 2 of R7003SB.
Channel Modes
The R7003SB is capable of changing its channel allocations as described in the table
below. Please choose the mode which suited the use in the following procedure from the
11 modes.
1
Press and hold down the Link/Mode button on the R7003SB receiver.
[Transmitter is always OFF]
2
Turn the receiver on while holding down the Link/Mode button. After power up,
the button can be released.
3
The LED should now be blinking red with green.
4
Each press of the Mode/Link button advances the receiver to the next mode.
[Refer to CH Mode table shown below.]
5
When you reach the mode that you wish to operate in, press and hold the
Mode/Link button for more than 2 seconds.
6
When LED blinks in green with red, it is the completion of a mode change.
7
Please cycle the receiver power off and back on again after changing the
Channel Mode.
*5 seconds after the receiver ON, LED shows CH Mode.
S.BUS2
S.BUS2 extends S.BUS and supports bidirectional communication. Sensors are connected
to the S.BUS2 port.
*Only S.BUS2 capable devices may be connected to the S.BUS2 port. Standard S.BUS
servos and gyros should not be connected to the S.BUS2 port.
R7003SB CH Mode table
©FUTABA CORPORATION 2016, 03 (2)
Mode
Port
LED blink
Port1 Port2 3/B S.BUS2
A(Default)
S.BUS
CH2
CH3
S.BUS2
Red 1 time
B
S.BUS2 Red 2 time
C
S.BUS
S.BUS
Red 3 time
D
CH1
Red 4 time
E
S.BUS2
Green 1 time
F
CH4
Green 2 time
G
CH2 Green 3 time
H
CH1 CH5 Green 4 time
I
CH2 CH7 Red and Green 1 time
J
CH4 CH8 Red and Green 2 time
K
CH11 CH12 Red and Green 3 time
Port
S.BUS Servo
S.BUS Gyro
S.BUS2 Servo
S.BUS2 Gyro
Telemetry sensor
S.BUS ×
S.BUS2 × (*)
R7003SB
[ Example: Connecting GYA431 to R7003SB CH Mode G ]
(GYA431 is used for the aileron of an airplane)
CH4
Rudder servo
CH6
2nd Aileron servo
CH2
Elevator servo
Port 1
Port 2
S.BUS2
3/B
CH1
Aileron servo
Battery
CH3
Throttle servo
GYA431
HUB
When using the R7003SB Receiver with the GYA430,
GYA431
The following table corresponds to the gyro's functions. A port can be used effectively.
The servo which a gyro controls is connected to a gyro.
* Please refer to the description of each gyro manual.
Gyro control CH CH Mode
Rudder D,E
Elevator F
Aileron G
Elevator+Rudder H
Aileron+Rudder I
Aileron+Elevator J
Aileron+Elevator+Rudder K
S.BUS Gyro Goup table
ZLWKH[WHUQDOSRZHU
LQSXWPXVWEHOHVVWKDQ9
7R0RWRU&RQWUROOHU
RU6HUYR
%UDQFK
)XVH
%ODFNOLQH
5HGOLQH
0RWRU
&RQWUROOHU
(;792/&$%/(
,WLVDWWDFKHGWR56%
2SWLRQ
(;792/&$%/(
WR3RUW
,WFKDQJHVLQWR(;792/0RGH
56%
WR0RWRU
EXT-VOL
3RZHU%DWWHU\RU
DQRWKHUSRZHUVXSSO\
IRUVHUYRV
*It connects with reference to the manual of CA-RVIN-700.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba R7003SB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba R7003SB in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info