Manual Futaba R6208SB (page 2 of 2) (English)

747955

Zoom out

Zoom in

1/2

S.BUS Servo Channel Setting Method

S.BUS

servo channel setting can be performed at the

R6208SB

receiver.

Connect the accessory short-plug to the

DATA

port of

the receiver.

Short-plug

(accessory)

* Connect the short-plug to the DATA port only when an S.BUS servo

channel is set. Normally do not connect the plug.

Connect an

S.BUS

servo to the conventional system

output connector(

) corresponding to the channel

you want to set.

Output

connector

Channel setting

Mode A Mode B

11 9

22 10

33 11

44 12

55 13

66 14

77 15

88 16

* Channel setting mode A (ch1 to 8 setting mode) or channel setting

mode B (ch9 to 16 setting mode) can be set.

Turn on the receiver.

* At once when turning on the receiver, the channel setting is com-

pleted in mode A.

(To switch to mode B, press the

Link/Mode

button until

the red and green

LED

starts to blink simultaneously.

The channel setting is completed in mode B.)

* The LED corresponding to the setting mode blinks.

Mode A: Red blinks 3 times

Mode B: Green blinks 3 times

Turn off the receiver.

Operation Mode Select

The operation mode is on "Normal mode" from factory

shipping. When to change the mode, please follow the steps

shown below.

Turn off the receiver.

Press and hold the

Link/Mode

switch and turn on the

receiver. Keep the switch hold more than one(1)

second. The

LED

starts flashing with the current

status.

Release the switch.

Turn off the receiver.

By doing this step, the mode can switch over between two(2)

modes.

0 to 1 sec. More than 1 sec.

0 sec. 1 sec.

Press and Hold

Turn on the receiver.

No function

Showing the CURRENT

mode with blink.

Red Blink = Normal

Green/Red Blink =

High Speed

Solid as the mode changed.

Red Solid = Normal

Green/Red Solid = High

Speed

(Become Red after one (1)

second)

㧔Function㧕

To change the mode between

Normal and High Speed

㧔LED

Status㧕

Please check the operation mode by observing the

LED

when

turning on the receiver. If possible there's no

FASST

transmitter

WXUQHGRQDURXQG\RXLQRUGHUWRPDNH¿UPHUFKHFN

When turn on the receiver, the

LED

will be;

• Red when on "Normal mode"

• Green and Red (makes Orange) when on "High Speed mode".

(After two(2) seconds, change to Red.)

If there are some

FASST

transmitter turned on around the

receiver, the

LED

may show the above status for a brief

moment then changed to the status indication as shown in the

LED

indication" table.

LED Indication

Green Red Status

Solid Solid Initializing

Off Solid No signal reception

Solid Off Receiving signals

Blink Off Receiving signals but ID is unmatched

Link to the transmitter

Press and hold the

Link/Mode

switch more than two(2)

seconds.

Re-adjust the F/S position (only for TM-8)

Press and hold the

Link/Mode

switch between one(1)

and two(2) seconds.

0 to 1 sec. 1 to 2 sec. More than 2 sec.

0 sec. 1 sec. 2 sec.

Press and Hold

No function

With TM-8

(not included in this set)

To set the F/S

position(No re-link)

Re-link(ID set) and to

set the F/S position

No function

Other than TM-8

(not included in this set)

Re-link(ID set)

WARNING

Do not perform the linking procedure with motor's

main wire is connected or the engine is operating as it

may result in serious injury.

While the linking is done, please cycle receiver

power and check if the receiver to be linked is really

under the control by the transmitter to be linked.

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Futaba R6208SB in the language / languages: English as an attachment in your email.

The manual is 0,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Futaba R6208SB Manual

Product: