747922
144
Zoom out
Zoom in
Previous page
1/183
Next page
144
Model menu (Airplane/Glider/Multicopter Functions)
Trim mix 1/2
[Corresponding model type]: Glider, general
These functions call the ailerons, elevators, and
Àaps (camber Àaps, brake Àaps) trim offset rates
preset according to the Àight state.
The amount of ailerons, elevator, and flaps
(camber Àap, brake Àap) trim offset can be set to
a switch.
As an example Trim mix 1 can be set up for
launching, with speed Àaps and ailerons dropped,
and a slight amount of up elevator. Trim mix
2 can be used for high speed flying, with both
ailerons and speed Àaps reÀexed slightly, and a bit
of down elevator.
The trim functions can be activated during
Àight by setting a switch. To prevent sudden trim
changes when switching Àight conditions, a delay
can be set to provide a smooth transition between
the two. Trim mix 2 will have priority over Trim
mix 1.
The offset rate of ailerons, flaps and elevators can be adjusted.
Tap to the corresponding setting item. Adjust the rate.
Example
1. Move to the [INH] item
.
Set the trim mix function to
[ON].
*When separating the settings for each condition, move to
the [Group] item and set it to [Single].
2. Select the ON/OFF switch.
3. Select the [Manual] or [Auto] mode.
In the [Auto] mode, also select an auto SW. This
switch can be linked to a stick, etc.
Speed!
In: The operation speed at switch ON can be set.
Out: The return speed at switch OFF can be set.
Fine Tuning!
The offset rate can be varied in the Fine Tuning
numeric range set at screen by VR, etc. selection.
Condition Delay!
When Áight conditions are set, the operation speed
can be set for each condition. Condition delay
operation can be interrupted and each rudder
Tuickly returned to its original position by selecting a
cut switch.
ŏ Select [Trim mix1 or 2] at the model
menu and call the setup screen
shown below.
When using this
function, Tap [INH].
(ON is displayed.)
The ON/OFF switch of
mixing is chosen.
Manual/Auto mode
selection
Manual: Switches the
function ON/OFF by
switch
Auto: Trim mix function
call can be linked to a
stick, etc. A stick switch,
etc. separate from the
function ON/OFF switch
is set.
Condition delay setting
Condition delay
cut switch
In speed
Out speed
(First)0∼27(Slowly)
*The display screen is an example. The actual
screen depends on the Model Type.
When a fine tuning VR is set,
the trim rates of ailerons,
flaps and elevators can be
adjusted.
To next page
ŏReturn to Model menu
The value inside the
parentheses shows the
current rudder position.
144


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FX36 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FX36 in the language / languages: English as an attachment in your email.

The manual is 11,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba FX36

Futaba FX36 User Manual - German - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info