747922
34
Zoom out
Zoom in
Previous page
1/183
Next page
34
Before Use
Rubber
grommet
Brass eyelet
Wood screw
Servo mount
ŶƈƕƙƒŃƏƈƄƇŃƚƌƕƈƖŃ
To prevent the servo lead cable from being
broken by vibration during flight provide a
little slack in the cable and fasten it at suitable
points. Periodically check the cable during daily
maintenance.
Fasten about 5-10cm
from the servo outlet so
that the lead wire is neat
and secure.
Margin in the lead wire.
ŰƒƘƑƗƌƑƊŃƗƋƈŃƓƒƚƈƕŃƖƚƌƗƆƋŃ
:hen mounting a power switch to an
airframe make a rectangular hole that is a little
larger than the total stroke of the switch so
that you can turn the switch 21/2FF without
binding.
Avoid mounting the switch where it can be
covered by engine oil and dust. In general it is
recommended to mount the power switch on the
side of the fuselage that is opposite the mufÀer.
ŶƄƉƈƗƜŃƓƕƈƆƄƘƗƌƒƑƖŃƚƋƈƑŃ
ƜƒƘŃƌƑƖƗƄƏƏŃƕƈƆƈƌƙƈƕŃƄƑƇŃ
ƖƈƕƙƒƖő
WARNING
Connecting connectors
Be sure to insert the connector until it
stops at the deepest point.
How to protect the receiver from vibration
and water
Wrap the receiver with something
soft such as foam rubber to avoid
vibration. If there is a chance of
getting wet, put the receiver in a
waterproof bag or balloon.
Receiver's antenna
Never cut the receiver's antenna. Do
not bind the receiver's antenna with
the cables for servos.
Locate the receiver's antenna as far as
possible from metals or carbon fiber
components such as frames, cables,
etc.
*Cutting or binding the receiver's antenna will
reduce the radio reception sensitivity and range,
and may cause a crash.
Servo throw
Adjust your system so that pushrods
will not bind or sag when operating
the servos to the full extent.
*If excessive force is continuously applied to a ser-
vo, the servo could be damaged due to force on
the gear train and/or power consumption causing
rapid battery drain.
Mounting servos
Use a vibration-proof rubber (such as
rubber grommet) under a servo when
mounting the servo on a servo mount.
And be sure that the servo cases do
not touch directly to the metal parts
such as servo mount.
*If the servo case contacts the airframe directly,
vibration will travel to and possibly damage the
servo.
ŰƒƘƑƗƌƑƊŃƗƋƈŃŶƈƕƙƒŃ
Switch
Less than 5 mm of
mounting plate
Attached screw
Switch cover
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FX36 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FX36 in the language / languages: English as an attachment in your email.

The manual is 11,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba FX36

Futaba FX36 User Manual - German - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info