747921
130
Zoom out
Zoom in
Previous page
1/174
Next page
130
<Model Menu (Airplane/Glider Functions)>
ŏ Select the function name
and return to the Model
menu by touching the
RTN button or pushing the
HOME/EXIT button.
<SensorTouch™>
RETURN
ELE to CAMBER
[Corresponding model type]: Airplane/glider, 2 ailerons or more
This function is used when you want to mix the
FDPEHUÀDSVZLWKHOHYDWRURSHUDWLRQ:KHQXVHG
the flaps are lowered by up elevator, and lift is
increased.
ŏ In-Áight mixing can be turned ON/OFF by assigning
this to a switch. (Always ON at [--] setting)
ŏ The mixing rate can be adjusted.
ŏ The point that has little effect near the neutral
position of the elevator stick can be adjusted.
(Glider only)
1RWH7KHHOHYDWRURQWKHWDLOOHVVZLQJZLOODOVR
EHHIIHFWHGZKHQWKLVPL[LVDFWLYDWHG
Ɣ0L[LQJUDWHDGMXVWPHQW
Move the cursor to the up or down mixing
rate item for each servo and touch the RTN
button to switch to the data input mode.
Adjust the rate independently by scrolling
the touch sensor.
Initial value: 0
Adjustment range: -100~100
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
Touch the RTN button to end the adjustment
and return to the cursor mode.
Setting method
Ɣ$FWLYDWHWKHIXQFWLRQ
Move the cursor to the [ACT] item and touch
the RTN button to switch to the data input
mode. Select the ACT mode by scrolling the
touch sensor.
*The display blinks.
Touch the RTN button to activate the
function and return to the cursor mode. (ON
is displayed.)
When setting a switch, move the cursor to
the [SW] item and touch the RTN button to
call the selection screen. Select the switch
and set its ON direction. (Always ON at "--"
setting)
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ5DQJHVHWWLQJ*OLGHURQO\
Move the cursor to the [RANGE] item and
hold the elevator stick to the desired position
(upper or lower side) and then touch the RTN
button for one second to set the range.
*The mixing does not work near neutral of the elevator stick.
Initial value: 0
Adjustment range: 0~100
(Glider: Currently selected condition name)
ŏ Select [ELE to CAMBER] at the Model menu
and access the setup screen shown below
by touching the RTN button.
*The display screen is an example.
The actual screen depends on the
model type.
Scrolling
ŏ Moving cursor
ŏ Selecting mode
ŏ Adjusting value
ŏ To next page
130


Need help? Post your question in this forum.

Forumrules
1

Forum

futaba-fx22

Reset search

  • How to set up throttle curve on Futaba FX22 radio control transmitter Submitted on 2-1-2025 at 23:19

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FX22 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FX22 in the language / languages: English as an attachment in your email.

The manual is 4,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info