747921

Futaba FX22 Manual

81
Zoom out
Zoom in
Previous page
1/174
Next page
81
<Functions of Linkage Menu>
ŏ Select the function name
and return to the Linkage
menu by touching the
RTN button or pushing the
HOME/EXIT button.
<SensorTouch™>
RETURN
THR CUT
Stops the engine safely and easily.(airplane and helicopter only)
Throttle cut provides an easy way to stop the
engine. Generally speaking, modelers will do so
E\ÀLSSLQJDVZLWFKZLWKWKHWKURWWOHVWLFNDWLGOH
The action is not functional at high throttle to
avoid accidental dead stick landings. The switch’s
location and direction must be chosen, as it defaults
to NULL.
Individually adjust the throttle cut activation
setting for each condition. (helicopter)
Throttle cut setting procedure
1. Activate the function:
Move the cursor to the [ACT] item and touch
the RTN button to switch to the data input
mode.
Select the ACT mode by scrolling the touch
sensor.
*The display blinks.
Touch the RTN button to activate the
function and return to the cursor mode.
2. Switch selection:
Move the cursor to the [SW] item and access
the switch setup screen by touching the
RTN button and select the switch and ON
direction.
*For a detailed description of the setting method, see [Switch
Setting Method] at the back of this manual.
3. Throttle cut position setting:
Move the cursor to the [POS] item and touch
the RTN button to switch to the data input
mode.
Adjust the servo operation position at throttle
cut operation by scrolling the touch sensor.
Initial value: 17
Adjustment range: 0~50
*When the RTN button is touched for one second, the servo
operation position is reset to the initial value.)
Touch the RTN button to end the adjustment
and return to the cursor mode.
*With the selected cut switch ON and the throttle stick at idle;
adjust the rate until the engine consistently cuts off.
However, be sure that the throttle linkage is not pulled too
tight or unreasonable force is not applied to the servo.
Designating a throttle cut setting position.
(helicopter)
*A throttle cut function acts in the low side of the throttle
position.
*"THRO" setting is common with all condition.
:DUQLQJ
Normal setting is slightly above idle.
1. To add the throttle cut position, use the
cursor to select the THRO percentage
desired, then press and hold the RTN button
for one second.
*Since conditions are not offered when an airplane is selected,
the throttle cut options will vary from the options noted
below.
*The throttle cut POS and SW settings are utilized for all
conditions.
*If the throttle cut switch is activated, or on, this status will
continue even if the condition is changed to an inhibited
setting.
*If the condition is inhibited (INH) the throttle cut is off if the
SW is in the off position and the throttle stick is low.
ŏ Select [THR CUT] in the Linkage menu and access
the setup screen shown below by touching the
RTN button.
ŏ Current throttle position
ŏ Individually adjust the Throttle Cut activation
setting for each condition. (helicopter)
ŏ Cut position
Scrolling
ŏ Moving cursor
ŏ Selecting mode
ŏ Adjusting value
ŏ Throttle
cut status
ŏ Throttle
cut status
ŏ Throttle
stick position
… 81 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FX22 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FX22 in the language / languages: English as an attachment in your email.

The manual is 4,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info