30078
4
Zoom out
Zoom in
Previous page
1/6
Next page
RECEIVER FP-R107N & SERVO FP-S138
Receiver, servos, switches, and battery
connections
Extension cord
Receiver crystal
7-channel FM receiver FP-R107N
Antenna wire
Landing gear
adapter
Switch
SSW-J
Charging plug
NR-4J
Fig.
9
The parts enclosed by the
dotted lines must be
purchased separately.
6th
CH
servo
(6NLK
only)
Landing gear
servo
Landing gear
servo
Rudder
servo
Throttle
servo
Elevator
servo
Aileron
servo
PRECAUTIONS
Connect the
receiver,
servos,
switches, and
battery
firmly
as
shown in Fig. 9. Then extend the transmitter and receiver
antennas fully.
Set the transmitter power switch to ON. Then set the receiv-
er power switch to ON. The servos stop near the neutral
position. Operate the transmitter sticks and check that each
servo follows the movement of the stick.
•Connect the pushrod to each servo horn, then check if
the
direction of travel of each servo matches the direction
of
operation of
its
transmitter
stick.
To
reverse
the
direction
of servo travel, switch the servo reversing switch.
Operate each servo over its full stroke, and check if the push-
rod binds or is too loose. Applying unreasonable force to the
servo horn will adversely affect the servo and quickly drain
the battery. Always make the travel of each control mecha-
nism somewhat larger than the full travel (including trim) of
the servo horn. Adjust the servo horns so that they move
smoothly even when the trim lever and stick are operated
simultaneously in the same direction.
Be alert for noise.
This set is noise-resistant, but is not completely immune to
noise. We recommend the use of noiseless parts.
•When installing the switch harness, cut a rectangular hole
somewhat larger than the full stroke of the switch and install
the switch so that it moves smoothly from ON to OFF. This
also applies to the switch mount when the switch is installed
inside the fuselage and is turned on and off from the outside
with a piece of wire, etc. Install the switch where it will not
be exposed to engine oil, dust, etc.
Fig.
10
Wood screw
with flat
washer
Rubber
bushing
Grommet
Plywood,
FRP board,
Aluminum
sheet
Flat washer
Rubber
bushing
Grommet
(Using plywood, FRP, or
aluminum sheet)
SERVO MOUNTING
(Using wood screws)
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FP6NLK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FP6NLK in the language / languages: English as an attachment in your email.

The manual is 1,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info