Manual Futaba CONQUEST (page 5 of 6) (English)

29057

Zoom out

Zoom in

1/6

• Even though the receiver antenna is long, do not cut or

bundle it.

• Install the servos securely. Tighten the mounting screws

until

the

rubber

grommet

crushed slightly.

the

screws

are

too

tight,

the

cushioning effect

will

adversely

affect-

ed.

• The crystal can be changed from the outside of the receiver

case. Always use the Futaba transmitter/receiver matched

crystal set to change the band.

• Spare servo horns are supplied. Use them as needed.

• Wrap the receiver in sponge rubber. Waterproof and dust-

proof the receiver by placing it in a plastic bag and wrapping

a rubber band around the open end of the bag. Do the same

with

the

receiver/servo

battery.

• Use the rubber bands wrapped around the receiver to hold

the servo and switch leads.

• After mounting is complete, recheck each part, then check

the range by making the transmitter antenna as short as

possible, extending the receiver antenna fully, and operating

the set from a distance of 20m to 30m. The movement of

each servo should follow the movement of each stick of the

transmitter.

• After mounting and checking are complete, take your model

to the shop where you purchased the set, or to an experienc-

ed radio control modeler, and ask them to teach you how to

handle your radio control set in the proper manner and to

inspect your set-up carefully.

•To

enjoy radio

control

models

fully,

be sure

observe

all

safety standards.

AILERON AND ELEVATOR DUAL (dual rate ON,

OFF) ADJUSTMENT (6NLKonly)

When the dual switch is set to ON, the servo throw is made

smaller by the amount shown by the hatched lines in Fig. 10.

The servo throw can be set from 40% to 100% of the total

travel by adjusting the trimmer next to the switch with a flat

bladed screwdriver. When the dual rate switch is set to OFF,

the throw is normal. When desiring a larger throw, such as for

spins, etc., set the dual rate switch to OFF and adjust the

throw mechanically by horn and rod adjustment. Set the

dual rate switch to on for level flight and adjust the trimmer

for the required amount of throw.

When the dual rate switch is set to OFF, dual rate is set and

the throw becomes large.

This horn permits shifting of the

servo neutral position at the servo

horn. Setting and shifting the

neutral position

a) Angle divisions

b) Effect

Fig.

1) The splined horn has 25 seg-

ments. The amount of change per

segment is; 360: 25=14.4°

2) The minimum adjustable angle

is determined by the number of

arms or number of the holes. For

four arms, the minimum adjustable

angle is:

To shift the holes center line to

the right (clockwise) relative to

baseline A, shift arm 2 to the po-

sition of arm 1 and set it to the

position closest to baseline A.

(Example] For a four arm horn,

the angular shift per segment is

14.4° . The shift to the right is 90°

(14.4

x6)

3.6°

To shift by the same angle in the

opposite direction, use the oppo-

site arm number.

Fig.

Arm 3 shift 4.8° to the right, arm

6 shifts 2.4° to the left,and arm 4

shifts 7.2° to the right and left.

For a six arm horn, turn the arm

counterclockwise and set arm 2

to the position of arm 1 . The ad-

justable angle is 60° - (14.4 x 4)

=2.4°.

Fig.

The following splined horns are optional.

Fig.

HORN A HORN B HORN C HORN D HORN E HORN P

The flag can be attached to, and removed

from, the end of the transmitter antenna

with one touch.

USING THE ANTENNA FREQUENCY FLAG

Insert the frequency flag into

the flag holder as shown here.

Fig. 17

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Futaba CONQUEST in the language / languages: English as an attachment in your email.

The manual is 1,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Futaba CONQUEST Manual

Product: