747972
20
Zoom out
Zoom in
Previous page
1/27
Next page
20
Expert Gyro and Governor Definitions and Tuning Section
*It does not display, when Opr.
mode is Gyro+THR, and when
SWASH-type is H4-00/H4-45.
*It does not display, when Opr.mode is
Gyro+THR, and when SWASH-type is
H4-00/H4-45.
*It does not display, when Opr.mode is
Gyro+THR, and when SWASH-type is
H4-00/H4-45.
G
OVERNOR
E
XPERT
S
ETTING
7KLVPHQXVHWVWKH*RYHUQRU([SHUWDOORZVWKHXVHUWRIXUWKHUUH¿QHWKHJRYHUQRUVHWWLQJV3XVKWKHPRGHRU±NH\IRUPRUHWKDQRQHVHFRQGRQWKH
*RYHUQRU%DVLFPHQXGLVSOD\WRJHWLQWRWKH*RYHUQRU([SHUWPHQX3XVKPRGHRU±NH\IRUPRUHWKDQRQHVHFRQGDJDLQRQWKH*RYHUQRU([SHUW
PHQXWREHUHWXUQHGWRWKH*RYHUQRU%DVLFPHQX
GOVERNOR EXPERT
MAP
(1) Governor Expert setting: start display
Push mode + or – key, to scroll through the editing menu. Pushing mode + or – key for more than
one second, brings you back to governor basic menu.
(2) Governor working mode [default: Governor]
Sets the governing type mode.
- Governor Mode – RPM is entirely controlled by the GOV once it has engaged. The GOV will do
whatever it takes to hold a constant RPM throughout flight.
- Limiter Mode – Throttle control follows the throttle curves to advance the throttle position during
flight, but controls the RPM during throttle reduction by not letting the RPM over speed past the
set RPM.
(3) Rv. Display [default: Rotor]
Ability to choose to display desired ROTOR RPM or MOTOR RPM.
(5) Yaw Comp [default: CW/TOP]
Yaw compensation allows the governor to more rapidly correct for changes in power demands of
the model resulting from yaw input. Set the mode to match the gyro installing direction, either CW/
TOP, CW/BOTM, CCW/TOP, CCW/BOTM by pushing the Set key. Pushing the RSET key inhibits
the function.
At the governor only mode, this parameter is inhibited.
CW: clockwise rotor direction
CCW: counter clockwise rotor direction
TOP: Gyro top/name emblem facing up
BOTM: Gyro top/name emblem facing down
(4) Feed Forward from Cyclic [default: 0%]
Increasing the value will add throttle with cyclic commands to aid in RPM stability.
(6) Revolution change up delay [default: 8] [ranges: 2 ~ 20]
How quickly the RPM changes when increasing RPM between two different RPM conditions and
flight modes. A higher number slows the RPM change rate; a lower value speeds up the RPM
change rate.
(7) Revolution down delay [default: 10] [ranges: 2 ~ 20]
How quickly the RPM changes when reducing RPM between two different RPM conditions and
flight modes. A higher number slows the RPM change rate; a lower value speeds up the RPM
change rate.
Push
DATA
+/– key
Push
MODE
+/– key
(8) Start delay [default: 5] [ranges: 2 ~ 20]
How quickly the RPM stabilizes to the set RPM from when the GOV is turned ON. A higher value
slows down the spool up rate; a lower value speeds up the spool up rate.
*It does not display, when Opr.mode is
Gyro+THR, and when SWASH-type is
H4-00/H4-45.
F/F.Cycl
0 %
Push
DATA
+/– key
Rv.Disp
Rotor
Rv.Disp
Engine
*It does not display,
when Opr.mode is
Gyro+THR, and
when SWASH-type
is H4-00/H4-45.
(9) Low revolution setting [default: 1000 rpm ]
This value is set to assign the lowest possible governing RPM. If the RPM is set below, or cannot
reach this RPM, the governor will not engage.
(10) Governor data reset
This parameter resets also the governor parameters to default settings. The “Exec.??” is displayed
by pushing data + or – key for confirmation. Pushing data+ or -key again completes the reset pro-
cess, displays “-Exec.-”, and returns to the start display. By pushing mode+ or – key during confir-
mation display, the reset process is aborted.
Push
DATA
+/– key
Push
DATA
+/– key
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba CGY750 V 2.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba CGY750 V 2.0 in the language / languages: English as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info