29013
2
Zoom out
Zoom in
Previous page
1/6
Next page
TRANSMITTER FP-T4NBL
Operating system : 2 stick, all channels
servo reverse
Transmitting frequency : 72 MHz bands
Modulation system : AM
(amplitude modulation)
Power requirement : 9.6V 500 mAH Nicad
Battery
Current drain : 150mA
RECEIVER
FP-R114H___________
Receiving frequency : 72 MHz bands
Crystal replacement system: Frequency can be
Intermediate frequency 455 kHz
Power requirement 4.8 V Nicd Battery
(shared with servo)
Current drain 18 mA (at 4.8 V)
Dimensions 1.3x1.87x0.78 in
(33x47.4x19.8mm)
Weight 0.9 5 oz (27.5 g)
Receiving range 500m on the ground
SERVO FP-S148
Control system
Operating angle
Power requirement
Current drain
Output torque
Operating speed
Dimensions
Weight
+putse width control
1520 us neutral
One side 45° or more
4.8V-6V
6.0V, 12mA (at idle)
42 oz-in (3kg.cm)
0.22 sec/60°
1.59x0.77x1.4 in
(40.4x19.8x36mm)
1.5oz
(44.4
g)
changed within the
same frequency band
by changing the pre-
cision crystal.
1000m in the air
with the FP-T4NBL
(under best conditions)
RECEIVER WITH LINEAR CONTROLLER MCR-4A
Dimensions
Weight
RECEIVER
Receiving frequency
Intermediate frequency
Current drain
Receiving range
AMP
Operating system
Voltage
Continuous maximum current
Momentary maximum current
Resistance loss
1.24x2.92x0.63 in (31.6x74.2x16.1mm)
(excluding protrusion at top)
1.5 oz (44.0 g) (excluding switches and
connectors)
72 MHz bands
455
kHz
26mA
500m on the ground 1000m in the air
with the FP-T4NBL
(under best conditions)
: idle to maximum speed, no brake, idle
point trimmer
:
6.0
to
8.4
V
:
100
A
:
450
A
: 0.01 ohm
SERVO FP S133
Control system
Operating angle
Power supply
Power consumption
Output torque
Operating speed
Dimensions
Weight
+ pulse width control 1520 us neutral
One side 40° or greater (including trim)
trim)
4.8V
or
6.0V
(shared
with
receiver)
6.0V, 8mA (at idle)
30.6 oz/in (2.2 kg.cm)
0.21 sec/60°
1.10 x 051 x 1.14 in (28 x 13x29 mm)
0.67
oz
(19g)
Antenna
Fig.
2
Neck strap bracket
Elevator trim lever
Power switch
Aileron trim lever
Transmitter
crystal
Servo
reversing
switches
Battery cover
Nonslip adjustable
lever head
TRANSMITTER FP-T4NBL
CONTROLS
Fig. 1 and Fig. 2 show the name
of each part of the transmitter.
Memorize the position and oper-
ation of each switch and control.
Level meter
Throttle
trim
lever
Handle
Rudder trim lever
Throttle
MODE II
Aileron
Elevator
Fig.1
Charging
jack
Rudder
In the following descriptions, all the servo reversing switches
are assumed to be in the normal position. When they are in the
reverse position, operation is the opposite of that described.
Rudder Rudder operation
Aileron trim lever Aileron trimmer
Elevator trim lever Elevator trimmer
Throttle trim lever Throttle trimmer
Rudder trim lever Rudder trimmer
Power switch ON in the up position
Level meter
Elevator and
Engine throttle
are opposite those shown in the
fiqure in Mode-l.
MODE I
This meter indicates the transmitter battery voltage.
When the antenna is extended fully and the power switch is
set to ON, the pointer should deflect to the silver zone.
Aileron Aileron operation
Elevator Elevator operation
Throttle Throttle operation
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba ATTACK_4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba ATTACK_4 in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info