29011

Futaba 9ZHP_part1 Manual

40
Zoom out
Zoom in
Previous page
1/78
Next page
System Section
Setting the Activation Switch
From many different commands, the switch setting
function may be displayed by pressing the
SWT
(
P
)
key. This causes a pictorial display of the available
switches to be displayed, as shown in the figure. In this
case, the Timer function will be used as an example.
The A-H keys are used to select a particular switch
location (in case you are confused about a switch's loca-
tion, each is labeled with its letter key). Once you press
the desired key location, the switch will be darkened on
the display. If you press the NUL key, switch activation
is disabled.
Once selected, you must choose the position of the
switch which defines the ON or OFF position. This is
done by pressing one of the two (or three, if a 3-position
switch) left-arrow keys P to R. If you are satisfied with
the choice, press the
PRE ( N
) key to get back to the
previous screen. If you have used the Timer as an exam-
ple, the switch you have chosen will be displayed at
the bottom of the timer definition area (if no switch is
chosen, "**" is displayed).
Setting STICK Activation
If you would rather have your on/off function con-
trolled by the motion of one of the transmitter sticks,
press the
STK (
O) button while in the switch setting
display. This displays the STICK SET function in the
lower part of the figure.
Use the J1 to J4 (A to D) buttons to select the
desired stick. Now, you will need to define the position at
which the switching occurs. To do this, hold the stick in
the desired location and press the
SET (Q
) key.
Finally, select the ON/OFF direction by pressing the
+/- (P) key (note that the
ACT
and
INH
posi-
tions swap each time the button is pressed). When you are
done setting up the stick switching, return to the original
setting screen with the
PRE (N
) key.
Setting Volume Controls
Some functions may be controlled by either stick
position or knobs/sliders (for example. Pitch Curve in the
Helicopter setup). In these functions, the
VOL
key will
appear at (O). Press the
VOL
key to get to the setting
screen. You may select the desired function to be set with
the right and left-arrow keys (A and R). Next, use the
F,
H,
J , or L keys to define which control selects the
volume. Now you must use the +/- key to choose the
operating direction of the control. Use the PRE key to
return to the previous menu.
The same procedure may be used if a stick control,
rather than a slider or knob, is desired. In this case you
will select the stick and direction as given earlier for the
"Setting Stick Activation" section above.
System Section, Page 38
… 40 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZHP_part1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZHP_part1 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info