29045
65
Zoom out
Zoom in
Previous page
1/78
Next page
Sailplane Section
Mode Setting
Offset Rate Setting
Aileron
Servo
Travel
Mode Selection Keys
To On/Off Switch
Setting Menu
Flap
Servo
Travel
To Previous Screen
Return To
Condition Menu
To Next Screen
Offset Position Setting
This sets the position where butterfly begins working.
Press the B key, then set the butterfly control (throttle
stick or left side knob) to the position to be set and press
the F ( SET ) key. We recommend one or two clicks
down from the high throttle position.
Aileron Servo Down Side Travel Setting
Press the C key and set the rate with the numeric
keys E to M . The setting range may vary from —100 to
+100% and the initial value is +50%. If you set the BFY
to be activated with the throttle stick moving down from
the top (full throttle) position, this setting has no effect
because motion is all on the Up side.
Aileron Servo Up Side Travel Setting
Press
the D
key
and
set
the rate
with
the
numeric
keys E to M . The setting range may vary from —100 to
+100% and the initial value is +50%. If you set the BFY
with the throttle stick, this setting is the important one.
Flaps Servo Down Side Travel Setting
Press the
NXT Q
key to get to the flap setting
menu. Then press the C key and set the rate with the
numeric keys E to M. The setting range may vary from
-100 to +100% and the initial value is +50%. If you set
up with throttle stick, this setting has no effect.
Flaps Servo Up Side Travel Setting
Press the
D
key and set the rate with the numeric
keys
E to M.
The setting range may vary from —100 to
+100% and the initial value is +50%. This is the effective
setting to make if throttle stick is used as mentioned
before.
ON/OFF Switch Setting
An ON/OFF switch is not defined initially. To define
one, display the switch setting screen by pressing the
SWT P
key. Use the keys to choose the switch and ON
direction you want. For a description of the switch setting
method, see page 40.
If you want BFY on all the time but don't like the
alarm, press the
SWT P
key, then press the
STK O
key, to get to the stick setting menu. Choose the throttle
stick
J3
and set it just above the offset position. Press the
SET Q
button to input the On position, then move
the throttle stick to be sure. You may need to switch
direction with the
+/- P
key.
Sailplane Section, Page 141
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZAP_part2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZAP_part2 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info