29045

Futaba 9ZAP_part2 Manual

11
Zoom out
Zoom in
Previous page
1/78
Next page
COLLECTIVE PITCH FUNCTION (CPT)
(DIVING
AIR
BRAKE,
HIGH
PITCH
TRIM)
Airplane Section
This function allows diving airbrake ("minus
pitch") adjustment at low throttle and high pitch
adjustment at high throttle for consistent model
speed during vertical aerobatics. This mixing can
be turned on and off during flight with a switch.
Air brake, engine idle-up trim, and the high-side
pitch control trim can be set independently.
The
mixing switching point (minus pitch/high pitch
switching point) can be set at a selected throttle
stick position, and each trim rate can be adjusted.
The throttle delay when switching from minus
pitch to high pitch and the pitch delay when
switching from high pitch to minus pitch can also
be adjusted independently.
Setting Up Collective Pitch Function
Activation of command
In the Condition Menu, press the
CPT
key to get the
COL PITCH menu shown below. Use the
A
key to activate mode setting, then press the ACT or
INH keys ( F and G ) to activate or inhibit the func-
tion.
Mode setting
Idle-up
High pitch
Trim Rate setting
ON/OFF switch
setting
Trimming volume
setting
Throttle delay
setting
Pitch delay
setting
Return to
Condition screen
Mixing operation
point setting
Mode selection
Switch Point Setting
Press the B key to enter the throttle position setting
function. Then set the throttle stick to the desired switch
point, and press the
SET (F)
key.
Idle-up Trim and Delay Setting
Press the C key to enter the Idle-Up Trim rate setting
function, and set the rate with the numeric keys F to
M. The range may be set from 0 to 100%, and the initial
value is set to 0%.
Next, press the P key to enter the Throttle delay
setting function, and set the delay with the numeric keys.
The setting range is 0 to 100%, and the initial value is set
to0%.
Pitch Control Trim Rate and Delay Setting
Press
the D
key
to enter the
Pitch
Trim
Rate
setting
function. Set the desired rate with the numeric keys F to
M.
The range may be set from 0 to 100%, and the initial
value is set to 50%.
Press the O key to activate the Pitch Delay setting
menu, and set the delay with the numeric keys
F to M .
The range may be set from 0 to 100% (initial setting is
0%).
On/Off Switch Setting
On initial setting, the activation switch for the Collec-
tive Pitch function is set as SW (E) ON at the lower posi-
tion. If you would like to change the switch or turn
mixing on all the time, call the Switch Setting screen by
pressing the
SWT
(
R)
key. Then use the keys to
choose the desired switch location and on direction. For
more information on the switch setting method, see page
37).
Idle-Up Trim/Pitch Control Trim Setting
You may set up the Collective Pitch function so that
its effect may be changed in flight by moving a trim con-
trol. The trim control allows you to adjust the volume by
moving a slider. At initial setting, the left-side lever is set
for idle-up trim and the right-side lever is set for pitch
control trim.
Call the volume setting screen by pressing the
VOL
O key, and select the desired control using the screen
menus (for a description of the volume setting method,
see page 37).
Use the
END
(N) key to leave this menu.
Airplane Section, Page 87
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZAP_part2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZAP_part2 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info