29047
17
Zoom out
Zoom in
Previous page
1/78
Next page
Manual Introductory Section
SYSTEM STATUS AND ALARM DISPLAYS
The PCM 1024Z System provides you with a
number of indicators and displays to show you
that your system is operating correctly. This sec-
tion will explain each display's function
EXT MEM ERR display
This display blinks when a data error occurred
during transmission of data between the trans-
mitter memory and the memory module. Turn
off the power. DO NOT REMOVE OR INSERT
THE MEMORY MODULE WITH THE POWER
TURNED ON. THIS ACTION COULD DE-
STROY THE MODULE.
ON AIR display and beep
This display is turned on when radio waves are
being transmitted.
Enter ID No. display
This display indicates when the security mode
is set. In this case, model data cannot be
changed. See the section on data protection to
reset this display.
LOW BATTERY display and beep
This display and warning beep are to notify the operator
that the transmitter battery is low.
TO PREVENT PROBLEMS, LAND THE MODEL
AS SOON AS POSSIBLE.
PLL ERROR and beep
This display blinks and sounds when the synthesized
frequency module is removed during operation.
Be sure to turn off power before installing the module.
Do not remove or insert the module with power on.
(D BACK-UP BATTERY FAILURE - DO NOT FLY
This warning is displayed when the data stored has been
lost for some reason. A beep will sound simultaneously.
When the power switch is turned on again, the error dis-
play goes off and the data returns to the factory default
state. The lithium data backup battery needs to be re-
placed, or there is a fault in the system. Return the
system to the Futaba service center for assistance. The
life of the lithium battery varies, but is usually at least
five years.
2 CURRENT MODEL IS*** ##.NAME ***
This display shows the model number and model name
currently stored in the active area of the transmitter. It
will disappear a few seconds after the system is turned on.
DATA PAC IS MISSING - LOADED MODEL1
This message is displayed whenever the transmitter is
turned on with the memory module removed and the
active model data was stored on the module. Without the
desired model data, the system loads the Model 1 data
instead.
3 CAUTION: NON-DEFAULT COND IS ACTIVE
This warning message is displayed, and a beep sounds,
whenever the transmitter is turned on with a flight con-
dition switch activated. This display and alarm will turn
off as soon as the flight condition switch is turned off.
4 CAUTION: SPECIAL MIX FNCT IS ACTIVE
This message and alarm are activated when the transmitter
is turned on with a mixing switch activated. The alarm
monitor above the power switch also blinks. All of these
will stop as soon as the mix switch is changed to its OFF
position.
CAUTION: ENGINE CUT FNCT IS ACTIVE
If the power is turned on with the engine cut switch on,
this message is displayed and a beep sounds. When the
engine cut switch is turned off, the display and alarm
stop.
Manual Introductory Section, Page 15
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZAP_part1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZAP_part1 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info