29043
8
Zoom out
Zoom in
Previous page
1/60
Next page
BATTERY CHARGING INSTRUCTIONS
(Transmitter and Receiver Nicd Batteries)
Before operating your system, recharge the Nicd batteries as follows:
•Connect the DIN connector of the FBC-8B (2)
battery charger to the transmitter charging
socket, and connect the 3P connector to the
airborne NR-4J Nicd battery pack and plug the
battery charger into a 120VAC outlet as shown
in the figure.
•The TX and RX LEDs light to show that bat-
teries are being charged. The Nicd batteries can
also be charged through the DSC-CHG cord by
connecting the CHG adaptor to the charger as
shown in the figure. This allows the NR-4J
airborne Nicd pack to be charged without
removing it from the model.
•Normally recharge the battery for about 15
hours. If it has not been used for some time,
discharge and recharge it two or three times,
then charge it a full 15 hours.
•The
amount of time
remaining
before the bat-
teries must be recharged can be estimated by
checking the integrated timer at the moment
the TX battery alarm sounds (antenna ex-
tended).
• Leaving batteries in the discharged state for a
long time will adversely affect their capacity
and life.
•The TX and RX Nicd batteries can be charged
simultaneously or independently.
•A fully-charged TX battery can be used for
about 10 flights of 10 minutes each. The air-
borne NR-4J Nicd battery pack can be used
for about 7 flights when 6 servos are used and
about 4 flights when 10 servos are used.
• The DSC (Direct Servo Controller)
system connects the signals from
the transmitter directly to terminal
C of the receiver through the DSC
cord and controls the servos with-
out transmitting radio waves. \\ is
extremely convenient when other
dyers are on the same frequency,
or during contests, etc.
When the DIN connector of the
DSC cord is connected to the DSC
socket, the power to the encoder of
the transmitter is turned ON auto-
matically The transmitter power
switch is left OFF.
• When not using the DSC, discon-
nect the DIN connector to reduce
battery drain.
To operate the servos, turn on the
airborne switch (only).
•When the DSC cord
is connected, the receiver
power supply voltage
is measured
(no load).
The voltage is displayed
by "Ex" on the lower
right side of the initial
LCD
screen.
NR-4J
Male
Female
DSC-CHG cord
Male
Female
Cut Here.
Male
Female
Male
Female
CHG
Adaptor
Female
Install the
accessory
DSC-CHG cord
(connector with tab)
to the side of
the aircraft fuselage
to use the charging
and DSC socket.
Charging
socket
and
DSC
connector
Female
Female
Receiver
DSC Cord
Make this connection
when using the DSC.
RX (Receiver)
TX (Transmitter)
AC-120V
Charger FBC-8B (2)
Charging Method
[6]
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9VAP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9VAP in the language / languages: English as an attachment in your email.

The manual is 3,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info