29049
70
Zoom out
Zoom in
Previous page
1/109
Next page
A LOOK AT THE RADIO'S GLID-SPECIFIC FUNCTIONS STEP BY STEP. Those functions which are identical to
the ACRO setups are referred directly to those pages.
MODEL TYPE: This function of the PARAMETER submenu is used to select the type of model programming to be used.
GLIDER TYPES:
Before doing anything else to set up a glider or sailplane, first you must decide which MODEL TYPE best fits your aircraft.
ACRO: for some aerobatic/slope gliders, ACRO is a better choice because of functions it offers that the GLID types do not.
ACRO provides:
SNAP-ROLL,
AILEVATOR (twin elevator servo support),
AIRBRAKE (a more assignable version of BUTTERFLY).
For nitro-powered sailplanes: IDLE-DOWN, THR-CUT, THROTTLE-NEEDLE mixing and THROTTLE DELAY programming.
But ACRO lacks programming for full-span ailerons and START and SPEED OFFSETS.
NOTE: This is one of the several functions that the radio requires confirmation to make a change.
GOAL of EXAMPLE: STEPS: INPUTS:
CH1
CH2
CH4
CH5
CH6
CH7
Glider2FLAP/2FL-C Configuration
CH1
CH2
CH4
CH6
CH6
CH7
Glider1FLAP Configuration
70
Change model 1 is MODEL TYPE
to GLID1FLAP.
.
NOTE: This is one of the several
functions that the radio requires
confirmation to make a change.
Where next?
Confirm you are currently using the
proper model memory. (Ex: 1)
Open PARAMETER submenu.
Change the MODEL TYPE.
Confirm the change.
Close.
On home screen, check model name
and number on top left.
If it is not the correct model (Ex: 1),
use MODEL SELECT, p. 25.
for 1 second.
(If Advance menu again.)
to 2nd page of menu.
1 step to PARAMETER.
to TYPE. to GLID1FLAP
for one second.
sure? Confirmation displays.
to confirm.
Remember: Now that you changed MODEL TYPE, the model memory is
almost completely reset. Only the modulation remains intact.
NAME the model: p. 27.
Change the receiver modulation from FM (PPM) to PCM or vice versa: see p. 30.
Utilize servo REVERS
E: see p. 31.
Adjust servo travel with END POINT: see p. 32.
Set up dual/triple rates and exponential (D/R,EXP): see p. 35.
GLID2FLAP/GLID2FL-C: The GLID2FLAP/GLID2FL-C MODEL TYPE supports dual flap servos that can also act as
ailerons, creating full-span ailerons and flaps. Additional flight conditions available (GLID2FL-C only). These
flight conditions contain different offset trims and aileron differentials to make the sailplane perform certain
maneuvers more easily.
GLID1FLAP: The GLID1FLAP MODEL TYPE is intended for sailplanes with one or two aileron servos (or none), and
a single flap servo (or two connected with a y-connector). This TYPE is meant to be a very simplistic version to set up
a basic glider without a lot of added features. Full-span ailerons are not possible in this MODEL TYPE.
70


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9CPsuper at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9CPsuper in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info