29049
16
Zoom out
Zoom in
Previous page
1/109
Next page
16
RADIO INSTALLATION
While you are installing the battery, receiver, switch harness and servos into your model’s fuselage, please pay attention to
the following guidelines:
Use the supplied rubber grommets when you mount each servo. Be sure not to
over-tighten the screws. If any portion of the servo case directly contacts the fuselage
or the servo rails, the rubber grommets will not dampen the vibration, which can cause
mechanical wear and servo failure.
Servo Throw
Once you have installed the servos, operate each one over its full travel and check that the pushrod and output
arms do not bind or collide with each other, even at extreme trim settings. Check to see that each control linkage
does not require undue force to move (if you hear a servo buzzing when there is no transmitter control motion, most
likely there is too much friction in the control or pushrod). Even though the servo will tolerate loads, any unnecessary
load applied to the servo arm will drain the battery pack quickly.
Switch Harness Installation
When you are ready to install the switch harness, remove the switch cover and use it as a template to cut screw holes
and a rectangular hole slightly larger than the full stroke of the switch. Choose a switch location on the opposite side
of the fuselage from the engine exhaust pipe, and pick a location where it can’t be inadvertently turned on or off
during handling or storage. Install the switch so it moves without restriction and snaps from ON to OFF and vice
versa.
Receiver Antenna
It is normal for the receiver antenna to be longer than the fuselage.
DO NOT cut or fold it back on itself — cutting or folding changes the electrical length of the antenna and may
reduce range. Secure the antenna to the top of the vertical fin, and let the excess wire length trail behind. You may run
the antenna inside of a non-metallic housing within the fuselage, but range may suffer if the antenna is located near
metal or carbon fiber pushrods or cables. Be sure to perform a range check before flying.
Receiver Notes
When you insert servo, switch or battery connectors into the receiver, note that each plastic housing has an align-
ment tab. Be sure the alignment tab is oriented properly before inserting the connector. To remove a connector from
the receiver, pull on the connector housing rather than the wires.
If your aileron servo (or others) are too far away to plug into the receiver, use an aileron extension cord to extend
the length of the servo lead. Additional Futaba extension cords of varying lengths are available from your hobby dealer.
Always use an extension of the proper length. Avoid plugging multiple extensions together to attain your desired length. If
distance is greater than 18” or multiple or high current draw servos are being used, use Futaba Heavy-Duty servo exten-
sions.
Receiver Vibration and Waterproofing
The receiver contains precision electronic parts. Be sure to avoid vibration, shock, and temperature extremes.
For protection, wrap the receiver in foam rubber or other vibration-absorbing materials. It is also a good idea
to waterproof the receiver by placing it in a plastic bag and securing the open end of the bag with a rubber band before
wrapping it with foam rubber. If you accidentally get moisture or fuel inside the receiver, you may experience inter-
mittent operation or a crash. If in doubt, send the receiver for service.
Wood screw
Rubber grommet
Brass eyelet
Servo moun
t
or rail
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9CPsuper at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9CPsuper in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info