WITCH E OR G*landing gear/ch 5GLID1FLAP = gearthrottle hold
S
WITCH F OR H*snap roll/trainertrainertrainer/THR-CUT
S
WITCH G OR E*noneback = SPEED OFFSET
fwd = START OFFSET
GLID2FL-C: OFFSET 1/2
idle-up 1 and 2
S
WITCH H OR F*noneGLID2FL-C: OFFSET 3idle-up3/ch 5/gyro
K
NOB Aflap/ch 6
(flap trim if FLAPERON on)
GLID1FLP: flap
(flap trim if FLAPERON on)
GLID2FLAP: camber
(flap trim if FL-AIL off)
HOVERING PITCH
KNOB Bch 8ch 8ch 8
K
NOB Cspoiler/ch 7
(disabled if AIL-DIFF on)
spoiler/ch 7
(disabled if AIL-DIF on)
HOVERING THROTTLE
K
NOB DnoneGLID1FLAP: ch 5none
S
LIDER Enonenonenone
*On the 9CA Mode 2 transmitters, the TOP LEFT SWITCHESare spring-loaded and 2-position; on the 9CA Mode 1, 9CH, and 9CP, those switches are
on the right side. For consistency, the switch position’s designation remains the same (upper left is F, etc), but the functions are moved to match the
switch type.
PUSH
Ni-Cd battery pack
Charging jack
Battery cover
Battery connector location
Trainer function
/DSC function connector
RF module
To remove, press the tabs together
and gently pull rearwards.
To install, line up the connector pins with
the socket in the rear of the module and
gently snap into position.
SWITCH ASSIGNMENT TABLE
• The factory default functions activated by the switches and knobs for a 9CA Mode 2 transmitter are shown below.
• Most 9C super functions may be reassigned to non-default positions quickly and easily.
• Basic control assignments of channels 5-9 are quickly adjustable in AUX-CH (see p. 39). For example, the channel 5
servo, which defaults to SWITCH E for retract use, can easily be unassigned (NULL) to allow for easy use as a second
rudder servo in a mix, or to a slider or dial for bomb door or other control.
• Note that most functions need to be activated in the programming to operate.
• 9CA Mode 1, 9CH, and 9CP transmitter functions are similar but reverse certain switch commands. Always check that
you have the desired switch assignment for each function during set up.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Futaba 9CPsuper at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Futaba 9CPsuper in the language / languages: English as an attachment in your email.
The manual is 8,92 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
