29041
14
Zoom out
Zoom in
Previous page
1/109
Next page
14
RECEIVER AND SERVO CONNECTIONS
Receiver
Output and
Channel
Aircraft (ACRO)
Glider (GLID1FLAP/GLID2FLAP/GLID2FL-C)
Helicopter (HELI)
1 ailerons/right aileron
1
/combined right flap & aileron
1
aileron (cyclic roll)
2 elevator elevator (cyclic pitch)
3 throttle throttle
4 rudder rudder
5 spare/landing gear/left aileron
1,3
/combined left flap and
aileron
2,3
right flap (GLD2FLAP/GLID2FL-C)
spare/gyro
6 spare/ flap(s)/combined left flap and aileron
2
pitch (collective pitch)
7 spare/left aileron
1
spare/governor
8 spare/second elevator servo
4
/mixture control spare
9 spare spare
1
Aileron Differential mode (AIL-DIFF). (See p. 47).
2
Flaperon mode. (See p. 45).
3
Using Second Aileron option, second aileron servo output is sent to channels 5 and 6 to allow use of a 5-channel receiver.
( AIL-2) (See p. 48)
4
AILEVATOR (dual elevator) mode. (See p. 50).
CHARGING THE Ni-Cd BATTERIES
Charging Your System’s Batteries
1. Connect the transmitter charging jack and airborne Ni-Cd batteries to the transmitter and receiver connectors of the charger.
2. Plug the charger into a wall socket.
3. Check that the charger LED lights.
The initial charge, and any charge after a complete discharge,
should be at least 18 hours to ensure full charge. The batteries
should be left on charge for about 15 hours when recharging the
standard NR-4J, NR4F1500 and NT8S700B Ni-Cd batteries.
We recommend charging the batteries with the charger sup-
plied with your system. Note that the use of a fast charger may
damage the batteries by overheating and dramatically reduce
their lifetime.
You should fully discharge your system’s Ni-Cd batteries periodically to prevent a condition called memory.
For example, if you only make two flights each session, or you regularly use only a small amount of the batteries
capacity, thememory effect can reduce the actual capacity even if the battery is fully charged. You can cycle your
batteries with a commercial cycling unit*, or by leaving the system on and exercising the servos by moving the
transmitter sticks until the transmitter shuts itself off. Cycling should be done every four to eight weeks, even during
the winter or periods of long storage. Keep track of the batteries capacity during cycling; if there is a noticeable
change, you may need to replace the batteries.
*Note that the 9C super transmitter system has electronic protection from overcharging and reverse polarity via a poli-switch. It does
NOT have a diode in the charge circuit and may be discharged/peak charged with the battery in the transmitter.
DO NOT attempt to charge your 8-cell transmitter pack on the 4-cell receiver plug of the wall charger!
Charger
TX: Transmitter charging indicato
r
RX: Receiver charging indicator
To transmitter charging jack
Receiver Ni-Cd battery
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9CHPsuper at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9CHPsuper in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info