29041
8
Zoom out
Zoom in
Previous page
1/109
Next page
8
MODULE: TP72-FM
• Module may be easily removed and a module on a different channel (or even band) reinserted to change the frequency on
which the 9C super transmits.
• Module transmits both FM (PPM) and PCM. No need for a second module.
All transmission circuitry is included in the module, so no retuning is needed when changing channels or even bands.
• Frequency band is changed by inserting a module on the proper band, including for international or ground model use.
In North America it is against FCC regulation to change the crystal within the transmitter module to a different
channel. All such transmitter crystal changes must be performed by a certified radio technician. Failure to properly tune
a system to its new channel may result in decreased range and may also result in interference to other types of frequency
users on adjoining channels. Doing so also voids your AMA insurance.
• The FSS synthesized module for the 9Z family of radios is NOT compatible with the 9Csuper.
• Radio system beeps and RF
LIGHT goes out to indicate module is not installed and radio is not transmitting.
• Non-Futaba brand modules are not FCC certified for use with this radio and therefore are against FCC regulation to use.
Doing so also voids your AMA insurance.
• TP75FM modules may also be used with the 9C super for ground use modules such as robotics, rocketry, trains, cars, and
boats.
RECEIVER: R138/R148/R149
• The R138 or R148 FM 8-channel or the R138 PCM 8-channel or R149 PCM 9-channel receiver included with your
system is a high-sensitivity narrow-band dual-conversion receiver.
• Note that your 9C super transmitter is capable of transmission on both PPM (FM) and PCM with just a simple program-
ming change and just turning the transmitter off and back on. (See p. 30.)
Any Futaba narrow band FM receiver (all produced after 1991) on the correct frequency band and frequency may be used
with the 9C super.
Any Futaba PCM 1024 receiver on the right frequency band and frequency may be used with the 9C super (all 1024
receivers say PCM1024; receivers which say PCM but not 1024 are 512 resolution and not compatible).
NEVER attempt to change a receiver’s band by simply changing crystal (IE removing a 72MHz crystal and inserting
a 75MHz crystal). A receiver that has a crystal installed from a different frequency band without retuning will not
receive properly and will have dramatically decreased range.
In North America the receiver included with this system may have its frequency changed by simply changing the crystal
as long as it remains in the same half the band. A low band receiver between channels 11 and 35 may be changed to any
other channel between 11 and 35 without requiring any tuning. A high band receiver between channels 36 and 60 may
similarly be changed. Receivers being changed from a high band channel to a low band or vice versa require proper
tuning and service by the Futaba Service Center.
SERVOS
• Please see technical specifications page for specifics on the servos included with your system.
• The included receiver is compatible with all J-plug Futaba servos, including retract, winch, and digital servos.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9CHPsuper at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9CHPsuper in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info