Manual Futaba 9CHFsuper (page 49 of 109) (English)

29009

Zoom out

Zoom in

1/109

There are 4 basic tail types in aircraft models:

 Simple. Model uses one elevator servo and one rudder servo (or multiple servos on a Y-harness). This is the default.

 Dual Elevator servos. Model uses 2 elevator servos. see AILEVATOR (ACRO) see p. 50.

 Tail-less model. Model uses 2 wing servos together to create roll and pitch control. see ELEVON(ACRO/GLID). see p. 49.

 V-TAIL. Model uses 2 surfaces, at an angle, together to create yaw and pitch control. see V-TAIL (ACRO/GLID ). see p. 51.

Note: Only one of the three tail-type functions (AILEVATOR, V-TAIL, and ELEVON) can be used at a time. The radio provides

a warning and will not allow the activation of another tail type until the first is deactivated. An error message of OTHER

WING MIXING IS ON will display. (See the wing type example on page 44.)

Using ELEVON(ACRO/GLID ): used with delta wings, flying wings, and other tailless aircraft that combine aileron and

elevator functions, using two servos, one on each elevon. The aileron/elevator responses of each servo can be adjusted

independently. This is also popular for ground model use, such as tanks, which drive two motors together for forward, and

one motor forward/one backward for turning.

Adjustability:

• Requires use of CH1 and CH2.

• Independently adjustable aileron travel allows aileron differential.

• Independently adjustable elevator travel allows for differences in

up vs. down travel.

NOTE: If ELEVON is active, you cannot activate FLAPERON, AIL-DIFF, or AILEVATOR. An error message OTHER WING

MIXING IS ON displays and you must deactivate the last function to activate ELEVON.

NOTE: Be sure to move the elevator and aileron sticks to full deflection during setup. If large travels are specified, when

the AILERON and ELEVATOR STICKS are moved at the same time the controls may bind or run out of travel.

(For details on setting up a complex aerobatic plane, such as "space shuttle" style controls, please visit

www.futaba-rc.com\faq\faq-9c.html. Many other setup examples are also available at this location.)

GOAL of EXAMPLE: STEPS: INPUTS:

Activate ELEVON.

Adjust aileron down travel to 90% of

up travel, creating aileron differential.

Where next?

Open the ELEVON function.

Activate the function.

Optional: adjust the up/down travel

separately for the servos as ailerons.

(Ex: down to 90%.)

Optional: adjust the elevator travel of

each servo. (Ex: right servo elev. travel

to 98%, left to 105%.)

Close menu.

for 1 second. (If basic, again.)

to ELEVON.

AILERON STICK. to 90%.

ILERON STICK to 90%.

to 98%.

to 105%.

Adjust individual servo's SUB-TRIMs: see p. 42 and END POINTs: see p. 32.

Set up dual/triple rates and exponential (D/R,EXP): see p. 35.

View additional model setups on the internet: www.futaba-rc.com\faq\faq-9c.html

[Note] When changing the polarity of a rate, "change rate dir?" is displayed for a check.

Please set up after pressing DIAL for 1 second and canceling an alarm display. (GLID only)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9CHFsuper in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Futaba 9CHFsuper Manual

Product: