29009
19
Zoom out
Zoom in
Previous page
1/109
Next page
19
WARNING & ERROR DISPLAYS
An alarm or error indication may appear on the display of your transmitter for several reasons, including when the trans-
mitter power switch is turned on, when the battery voltage is low, and several others. Each display has a unique sound
associated with it, as described below.
MODEL SELECTION ERROR: Warning sound: 5 beeps (repeated 3 times)
The MODEL SELECTION warning is displayed when the transmitter attempts to load a model memory from a memory
module (optional CAMPac) that is not currently plugged into the transmitter. When this occurs, model No. 01 is automati-
cally loaded.
Do not fly until the proper model is loaded into memory! Reinsert the memory module, and
recall the desired setup using the model select function.
LOW BATTERY ERROR: Warning sound: Continuous beep until transmitter is powered off.
The LOW BATTERY warning is displayed when the transmitter battery voltage drops below 8.5V.
Land your model as soon as possible before loss of control due to a dead battery.
MIXER ALERT WARNING: Warning sound: 5 Beeps (repeated until problem resolved or overridden)
The MIXER ALERT warning is displayed to alert you whenever you turn on the transmitter with any
of the mixing switches active. This warning will disappear when the offending switch or control is
deactivated. Switches for which warnings will be issued at power-up are listed below:
ACRO:Throttle cut, idle-down, snap roll, airbrake GLID:Butterfly, Start and Speed mixing HELI:Throttle cut, throttle hold, idle-up
If turning a switch OFF does not stop the mixing warning: When the warning does not stop even when the mixing switch
indicated by the warning display on the screen is turned off, the functions described previously probably use the same
switch and the OFF direction setting is reversed. In short, one of the mixings described above is not in the OFF state. In this
case, reset the warning display by pressing both S
ELECT BUTTONS simultaneously. Then change one of the switch settings
of the mixings duplicated at one switch.
BACKUP ERROR: Warning sound: 4 beeps (repeated continuously)
The BACKUP ERROR warning occurs when the transmitter memory is lost for any reason. If this occurs, all of the data will
be reset when the power is turned on again.
[Note] At this warning display, the transmitter transmits in PPM mode even if the set-up mode is PCM mode.
Do not fly when this message is displayed — all programming has been erased and is not avail-
able. Return your transmitter to Futaba for service.
MEMORY MODULE INITIALIZE DISPLAY
This warning appears when an (optional) CAMPac memory module is used in the transmitter for the first time. When the
M
ODE BUTTON is pressed, initialization of the module begins, after which the memory module can be used. Once the
module is initialized, the display will not appear again.
The 9C super CANNOT convert data from other radio types (ie. 8U, 9Z). Installation of a CAMPac with data from
another radio type will result in reinitialization of the CAMPac and loss of all data.
RF MODULE WARNING: Warning sound: A single long beep. The single beep lets you know that the RF module has been
removed from the transmitter, or is not being read properly. The green RF light also goes out.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9CHFsuper at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9CHFsuper in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info