29007
91
Zoom out
Zoom in
Previous page
1/109
Next page
OFFSET: Optional separate trims in addition to those for the normal condition. This function is used to automatically change
the trim of a helicopter, for example, when transitioned from hover to flying at high speed. A clockwise-rotation rotor
helicopter tends to drift to the right at high speed, so an aileron offset may be applied to offset the helicopter to the left.
The necessary elevator offset varies with model geometry, so it must be determined by noting collective pitch changes at
high speed. The rudder offset is affected by both revo. mixing and trim lever movement while in the offset function.
Adjustability:
Complete switch assignability, plus a CONDITION option that creates/switches between individual trims for each of the
idle-ups.
When OFFSET is active (its switch is on), moving the T
RIM LEVERS adjust the stored offset, notthe trims in the normal
condition.
When OFFSET is inactive (its switch is off), the OFFSET and any trim adjustments to it have no effect (model obeys the
trim settings of the currently-active flight condition.)
Defaults to ON.
When OFFSET is inhibited, trim adjustments made in any flight condition affect all flight conditions.
Rapid jumps caused by large offsets can be slowed using the DELAY function.
NOTE: Remember, offsets and revo. mixes are not recommended when using heading-hold/AVCS gyros because they
conflict with the automatic corrections to trim and torque that AVCS provides.
GOAL of EXAMPLE: STEPS: INPUTS:
91
Set up separate trims for each of the
three idle-up conditions.
Adjust the idle-up 2 rudder trim to
correct for torque at high speeds.
Where next?
Open the OFFSETfunction.
Change switch setting to COND
Select IDL2
.
Adjust trim settings as needed. (Ex:
rudder to +8%.)
Close menus and confirm difference in
trims between normal and idle-up 2.
for 1 second.
(If basic, again.)
to OFFSET.
to COND .
to IDL2.
to +8%.
E (9CH) or G (9CA) from
NORMAL to IDL2. Check that rudder
trim changes.
DELAY: see p. 92.
THR-HOLD: see p. 88.
Setting up the Idle-Ups: Throttle and Collective pitch Curves and Revo. Mixing
(TH-CURVE, PIT-CURVE, REVO. MIXING for idle-ups: see p. 90.
*During OFFSET operation, the aileron, elevator, and rudder travels are displayed on each trim display in the Startup screen.
91


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9CAPsuper at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9CAPsuper in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info