29007

Futaba 9CAPsuper Manual

88
Zoom out
Zoom in
Previous page
1/109
Next page
HELI-SPECIFIC ADVANCE MENU FUNCTIONS
THR-HOLD: This function holds the engine in the idling position and disengages it from the T
HROTTLE STICK when SWITCH
E (9CH) or G (9CA) is moved. It is commonly used to practice auto-rotation.
Prior to setting up THR-HOLD, hook up the throttle linkage so that the carburetor is
opened fully at high throttle, then use the digital trim to adjust the engine idle
position. To have THR- HOLD maintain idle, move the T
HROTTLE STICK to the idle
position, then move the hold SWITCH on and off and keep changing the offset value
until the servo does not move. To lower the engine idle speed, or if you want to shut
off, input a more negative number.
Adjustability:
Idling position: Range of -50% to +50% centered about the throttle idle position to get the desired engine RPM.
Rudder offset:Offsets the tail rotor pitch. Keeps the fuselage from rotating in throttle hold.
Time delay: A rudder offset time delay may be set up within the DELAY function (see p. 92) to ease in rudder and
prevent tail wag.
Throttle curve: Since the throttle is moved to a single preset position, no curve is available for THR-HOLD.
Collective pitch curve: Independent curve, typically adjusted to create a blade pitch range of -4% to +10% to +12%,
Revo. mix: Since revo. mix adjusts for torque from the engine, no revo. mix is available for THR-HOLD .
Priority: The throttle hold function has priority over idle-up. Be sure that the throttle hold and idle-up S
WITCHES are in the
desired positions before trying to start the engine. (We recommend starting your engine in throttle hold for safety reasons.)
Gyro: Gyro programming includes an option to have a separate gyro setting for each condition, including THR-HOLD .
This avoids the potential problem of the user being in the wrong gyro setting when going to THR-HOLD , resulting in an
improper rudder offset and the model pirouetting.
GOAL of EXAMPLE: STEPS: INPUTS:
88
Set up throttle hold.
Determine desired throttle position by
idling engine, turn on THR-HOLD , and
adjust percentage as required to reach
the desired running point.
Where next?
Open THR-HOLD function.
Activate the function.
Set desired engine position.
Optional: set up a rudder offset. (If a
slowed reaction is desired, go to DELAY.)
Close.
for 1 second.
(If basic, again.)
to THR-HOLD.
to OFF.
to desired percent.
to OFF.to desired offset.
PIT-CURVE for THR-HOLD: see p. 90.
DELAY for THR-HOLD (to ease collective pitch response): see p. 92.
GYRO setup: see p. 95.
Setting up the Idle-Ups: Throttle and Collective pitch Curves and Revo. Mixing
(TH-CURVE, PIT-CURVE, REVO. MIXING) for idle-ups: see p. 90.
D/R,EXP
: see p. 35.
is automatically activated with THR-HOLD.
•
•
•
•
•
•
•
•
•
Switch assignment: Assigned to SWITCH G (9CA) or E (9CH) down.
Adjustable in the SW SELECT (T-HOLD item).
(2-position type switch only)
… 88 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9CAPsuper at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9CAPsuper in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info