29001

Futaba 8UAPS Manual

87
Zoom out
Zoom in
Previous page
1/105
Next page
83
The Hovering Throttle function may be used to trim the throttle near hover without
affecting pitch. Its position can be memorized so that when the model memory is recalled,
the original trim is repeated by rotating the knob to its center position.
When the hovering throttle knob is turned clockwise, the engine speed rises and when
turned counterclockwise, the engine speed drops. Changes in rotor speed caused by
temperature, humidity, or other conditions can be accommodated. When used with the
hovering pitch function, more exact trimming is possible.
Working with Hovering Throttle
To HOV-PI
function
To PMIX-2
function
Current trim position
Range: -100 to +100%
(Initial value: 0%
Data input keys
These keys are used to move
through the two submenus in
the HOV-TH function.
2. Trim memory setting
Press the (+)/(-) keys
simultaneously to enter the current
knob location. When the hovering
throttle knob is returned to the
center, the trim returns to its
position before memorization.
Note that when memorization is
repeated with the knob offset from
center, the trim value accumulates.
Current trim memory
Range: -100 to +100%
(Initial value: 0%)
1. Activate Hovering Throttle Function
Press the (+) key to activate the HOV-TH function ("ON" or
"OFF" will be displayed, depending on the IDL-UP switch's
position). Use the (-) key to INH
ibit the mixer.)
• If you wish to reset to the initial value, make the trim position 0%
with the knob and memorize the trim, then return the knob to its
center position.
The Hovering Pitch function may be used to trim the rotor pitch near hover without
affecting throttle. Its position can be memorized so that when the model memory is recalled,
the original trim is repeated by rotating the knob to its center position.
When the hovering pitch knob is turned clockwise, the rotor pitch increases, and
when turned counterclockwise, the rotor pitch decreases. Changes in rotor speed
caused by temperature, humidity, or other conditions can be accommodated. When
used with the hovering throttle function, more exact trimming is possible.
Using the Hovering Pitch Function
To GYRO
function
To HOV-TH
function
Current trim position
Range: -100 to +100%
(Initial value: 0%
Data input keys
These keys are used to move
through the two submenus in
the HOV-PI function.
2. Trim memory setting
Press the (+)/(-) keys
simultaneously to enter the current
knob location. When the hovering
pitch knob is returned to the center,
the trim returns to its position before
memorization.
Note that when memorization is
repeated with the knob offset from
center, the trim value accumulates.
Current trim memory
Range: -100 to +100%
(Initial value: 0%)
1. Activate Hovering Pitch Function
Press the (+) key to activate the HOV-PI function ("ON" or
"OFF" will be displayed, depending on the IDL-UP switch's
position). Use the (-) key to INH
ibit the mixer.)
• If you wish to reset to the initial value, make the trim position 0%
with the knob and memorize the trim, then return the knob to its
center position.
… 87 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 8UAPS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 8UAPS in the language / languages: English as an attachment in your email.

The manual is 4,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info