28997
39
Zoom out
Zoom in
Previous page
1/82
Next page
TRIM submenu: resets and adjusts effectiveness of digital trims.
The 7CA has digital trims which are different from conventional mechanical trim sliders.
Each TRIM LEVER is actually a two-direction switch. Each time the TRIM LEVER is
pressed, the trim is changed a selected amount. When you hold the TRIM LEVER, the trim
speed increases. The current trim position is graphically displayed on the start up screen.
The TRIM submenu includes two functions that are used to manage the trim options.
HELI models only: OFFSET is available in the idle ups. If OFFSET is inhibited, adjustment of the TRIM LEVERS will adjust the
trims for all flight conditions. If OFFSET is active, then moving the trims within any one condition will affect only that
condition. See OFFSET,p.70.
Trim reset (CLR): electronically centers the trims to their default values. Note that the SUB-TRIM settings and the trim
STEP rate are not reset by this command.
GOAL of EXAMPLE: STEPS: INPUTS:
Trim step: changes the rate at which the trim moves when the TRIM LEVER is activated. It may be set from 1 to 40
units, depending on the characteristics of the aircraft. Most ordinary aircraft do well at about 2 to 10 units. Generally larger
trim steps are for models with large control throws or for first flights to ensure sufficient trim to properly correct the model.
Smaller trim steps are later used to allow very fine adjustments in flight.
GOAL of EXAMPLE: STEPS: INPUTS:
39
Reset trims to neutral after having
adjusted all linkages.
NOTE: This is one of several
functions for which the radio requires
confirmation to make a change.
Where next?
Open BASIC menu, then open
TRIM submenu.
Request and confirm the reset.
Close.
for 1 second.
(If ADVANCE, again.)
to TRIM.
for 1 second.
Beep sounds.
Adjust SUB-TRIMs: see p. 40.
Adjust trim rate (STEP): see below.
Adjust END POINTs: see p. 32.
Set up dual/triple rates and exponential (D/R,EXP): see p. 34.
Double the sensitivity (larger step) of
the AILERON TRIM LEVERS for a first
flight of an aerobatic model to ensure
sufficient range to trim the model for
level flight.
Where next?
Open
Choose the STEP you wish to change.
(Ex: aileron)
TRIM submenu.
Adjust the size of the step. (Ex: incr. to 8)
Repeat as desired for other channels.
Close.
for 1 second.
(If ADVANCE, again.)
to TRIM.
to 8.
to CH1.
to ELEV.tonew setting.
Repeat as needed.
Adjust sub trims: see p. 40.
Adjust END POINTs: see p. 32.
Set up dual/triple rates and exponential (D/R,EXP): see p. 34.
.
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 7CAP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 7CAP in the language / languages: English as an attachment in your email.

The manual is 2,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba 7CAP

Futaba 7CAP User Manual - Dutch - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info