28993

Futaba 6XH Manual

59
Zoom out
Zoom in
Previous page
1/64
Next page
2. Now press the
CURSOR
key twice, this
will cause the plus or minus sign in front
of the large number to flash on and off.
You can set the direction of revolution
mixing on each side of the half-throttle
position by changing this flashing sign
with the (+) or (–)
DATA INPUT
keys.
Therefore, you’ll either set plus or minus
for both sides of the throttle stick’s motion
(indicated by the
R/U
or
L/D
indicator in
the window).
Use the (+) or (–) key to match the mixing
direction to the rotor rotation: (–) gives
right rudder, (+) gives left rudder. Verify
that you get the proper motion of the
rudder channel when you move the
throttle. You’ll set the amount of travel in
the next step.
3. Again press the
CURSOR
key; this will
cause the small percent sign in front of the
large number to flash on and off. At this
point you choose the percentage of revo
mixing for both sides of half throttle. You
may set a value of 0% to 100% for each
side by moving the throttle stick in both
directions, one at a time, and changing the
percentage number to suit. Now verify
that the rudder responds both the correct
direction and amount for travel on both
sides with the master control. If you wish
to return the mixing percentage to the
default 50% value, press both the (+) and
(–) keys simultaneously.
R-OF — Rudder Offset
The rudder offset function is used to change the neutral position (offset) of the rudder
when switch E is used to switch to idle-up. This function may be used to automatically change
the trim of a helicopter flying at high speed. A clockwise-rotation rotor helicopter tends to drift
to the right at high speed, so a rudder offset may be applied to yaw the helicopter to the left.
The necessary offset varies with model geometry, so it must be determined by noting
changes at high speed. The rudder offset is affected by both revolution mixing and trim.
Rudder offset is turned on at the same time as idle-up, switched by switch D.
Setting up Rudder Offset
1. Press one of the
MODE SELECT
buttons
until the
R-OF
window appears. The
default is for the function to be inhibited.
To activate, press the
CURSOR
key, then
press the (+)
DATA INPUT
key. This will
cause the flashing
INH
display to change to
a flashing
ON
or
OFF
display, depending
on the idle-up switch’s position.
2. Press the
CURSOR
key once. The percent
indicator should begin flashing.
3. Now you can adjust the rudder offset
position with the (+) or (–)
DATA INPUT
keys, anywhere between -100 and +100%
– 54 –
… 59 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 6XH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 6XH in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba 6XH

Futaba 6XH User Manual - Spanish - 55 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info