28989

Futaba 6XA Manual

9
Zoom out
Zoom in
Previous page
1/64
Next page
CHARGING THE Ni-Cd BATTERIES
1. Connect the transmitter charging cord into the charging socket (on the right of the case,
when facing the front) and airborne Ni-Cd batteries to the receiver connector on the
charger.
2. Plug the charger into a wall socket.
3. The charger’s LEDs should light, indicating charging current is flowing. The batteries
should be left on charge for about 15 hours.
Only charge the batteries with the charger supplied with
your system. The use of a fast charger may damage the batteries by overheating and
dramatically reduce their lifetime.
You should fully discharge your system’s batteries
periodically to prevent a condition called “memory.” For example,
if you only make two flights each session, or you regularly use only a small amount of the
batteries’ capacity, the memory effect can reduce the actual capacity even if the battery is
fully charged. You can cycle your batteries with a commercial cycling unit, or by leaving the
system on and exercising the servos by moving the transmitter sticks. Cycling should be
done every one to two months, even during the winter or periods of long storage. Keep track
of the batteries’ capacity during cycling; if there is a noticeable change, you may need to
replace the batteries.
NOTE: If you need to remove or replace the transmitter battery, do not pull on its wires to
remove it. Instead, gently pull on the connector’s plastic housing where it plugs in to the
transmitter.
Operating With The Trainer Cord
An optional training cord is available from your dealer. The cord may be used to help
a beginning pilot learn to fly easily by allowing a second transmitter, operated by an
experienced instructor, to be connected to this system. The instructor may override the
beginning pilot at any time to bring the model back under safe control. For training, the
T6XAs/ T6XHs transmitter may be connected to another T6XAs/XHs system, as well as to
any 4VF, 6VA Skysport, 6XA, Super 7, System 8, or 9Z series transmitter.
To use the trainer cord:
1. Set up both the student’s and instructor’s transmitters to have identical trim and control
motions. If the instructor’s transmitter is on a different frequency than the student’s, use
the student’s as the master transmitter and the other as the student’s.
– 4 –
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 6XA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 6XA in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba 6XA

Futaba 6XA User Manual - Spanish - 55 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info