28987
5
Zoom out
Zoom in
Previous page
1/24
Next page
5
Charging jack - Port for charging the transmitter batteries with the included battery charger. On-off switch
On/off switch
DATA INPUT lever - Used to change the values of the various functions displayed on the LCD screen
Liquid - crystal display screen (LCD) - Displays programming modes and values entered.
MODE key - Used to scroll through and display the “13” or “14”(PCM) different functions.
SELECT key - Used to display the values for the current function.
Throttle – cut button - To use the throttle-cut function, lower the throttle stick all the way, then Push the throttle-cut button to
fully close the carburetor and shut of the engine.
Throttle/rudder control stick - Operates the servos connected to channel 3 (throttle) and channel 4 (rudder) in the receiver.
Idle – up switch - This switch operates to change the fight condition which is set the throttle curve and pitch curve of mid air
maneuvers (rolls, loops, stall turns) and 3D flight.
Gyro switch/Channel 5 - You can connect the sense adjust connector to the channel 5 of the receiver to operate the gyro
which has two different sense. Also if you use Futaba GY401/502/601 Gyro, two different gyro senses setting on gyro function
in this transmitter can be call by this switch.
Antenna - Radiates signals to the receiver. Never fly a model without fully extending the antenna or you may create
interference to other modelers and decrease operational signal range of the transmitter. The antenna may be removed and
replaced with another in case it is inadvertently broken.
RADIO INSTALLATION
Follow these guidelines to properly mount the servos, receiver and battery.
INPORTANT!: Please use PCM receiver if the composition parts of the model used much metal, carbon graphite etc.
because they will generates quite a lot of the noise.
Make certain the
alignment tab on the battery, switch and servo connectors is oriented correctly and “keys” into the
corresponding notch in the receiver or connectors before plugging them in. When unplugging connectors, never pull on the
wires. Always pull on the plastic connector instead.
If any servo wires are not long enough to reach the receiver, servo extension wires (available separately) may be used.







Always mount the servos with the supplied rubber grommets. Do not over tighten the
screws. No part of the servo casing should contact the mounting rails, servo tray or any other
part of the helicopter structure. Otherwise, vibration will be transmitted to the servo causing
premature wear and/or servo failure.
Note the small numbers (1, 2, 3, 4) molded into each arm on the Futaba 4-arm servo arms. The
numbers indicate how many degrees each arm is “off from 90 degrees to correct for minute
manufacturing deviations from servo to servo.
To center the servos, connect them to the receiver and turn on the
transmitter and receiver. Center the trims on the transmitter, then find
the arm that will be perpendicular to the pushrod when placed on the
servo.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 6EXHP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 6EXHP in the language / languages: English as an attachment in your email.

The manual is 3,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info