FUTABA ACCESSORIES AND REPLACEMENT PARTS
REPLACEMENT PARTS
ACCESSORIES
Flight packs since your Futaba 6EXA transmitter holds memories for up to six models, there is no need to purchase a complete radio
system (including the transmitter) for every model you fly. Available separately, Futaba Flight Packs contain a receiver, servos, switch,
battery and all servo mounting hardware. Consult your dealer or the Futaba Service Center for specific contents and order numbers.
Receiver crystals:
The receiver frequency may be changed as long as it remains within the “low” and “high” band frequency range. If your receiver is
on any channel from 11 through 35, it is a “low band” receiver and the frequency may be changed to any other channel from 11
through 35 without having to perform any other service. Simply purchase a crystal on the desired channel, then replace the existing
crystal in your receiver with the new one. If your receiver is on any channel from 36 through 60, it is a “high band” receiver and the
frequency may be changed to any other channel from 36 through 60. To order a receiver crystal, replace the “**” in the order
numbers below with the required channel number. (To order a receiver crystal on channel 30, order FUTL5730.)
FM Dual Conversion 72 MHz low band (channels 11 – 35) receiver crystal – FUTL57**
FM Dual Conversion 72 MHz high band (channels 36 – 60) receiver crystal – FUTL58**
Note: Should you ever wish to change the transmitter frequency, the transmitter must be sent to the Futaba Service Center for retuning.
FTA-8 Neck strap.....................................................FUTM5692
NR-4K 4.8 Volt, 250 mAh receiver battery.........FUTM1210
NR-4B 4.8 Volt, 1,000 mAh receiver battery......FUTM1380
NR-4F 4.8 Volt, 1,500 mAh receiver battery ......FUTM1285
AEC-3 8" [200mm] Servo Extension....................FUTM3910
AEC-14 8" [200mm] Heavy Duty Servo Extension
(for digital servos)...................................................FUTM4140
AEC-11 16" [400mm] Servo Extension...............FUTM3955
AEC-15 16" [400mm] H.D. Servo Extension
(for digital servos)...................................................FUTM4145
AEC-16 Dual H.D. Servo Extension
(Y-connector, for digital servos) ............................FUTM4135
AEC-13 Dual Servo Extension (Y-connector).......FUTM4135
SR-10 Dual Servo Reverser...................................FUTM4150
Trainer Box transmitter..........................................FUTM4375
(if using with 6EXA transmitter use the MD-TC trainer cord)
MD-TC trainer cord..................................................FUTM4420
MM-TC trainer cord.................................................FUTM4415
ANT-5 Transmitter antenna ...................................FUTM5040
NR-4J 4.8 Volt, 600 mAh receiver battery..........FUTM1280
NT-8F 600B 9.6 Volt,
600 mAh Transmitter battery...............................FUTM1440
SWH-13 Switch Harness w/charge plug .............FUTM4370
FSH-6X 4-arm servo arm.......................................FUTM2030
FSH-6S 6-arm servo arm.......................................FUTM2010
FSH-32 Servo mounting screws (10)...................FUTM2250
MODEL DATA RECORDING SHEET
(Make copies before using)
Model name _________________________
Model No. 1 • 2 • 3 • 4 • 5 • 6
MENU FUNCTION CH 1 CH 2 CH 3 CH 4 CH 5 CH 6
REVERSE Servo Reverse N • RN • RN • RN • RN • RN • R
D/R Dual Rate settings ▲ % ▼ % ▲ % ▼ %
E.P.A End Point Adjust ▲ % ▼ % ▲ % ▼ % ▲ % ▼ % ▲ % ▼ % ▲ % ▼ % ▲ % ▼ %
TRIM Trims ±±±±
D/R Exponential Settings ▲– %▼– % ▲– %▼– %
MIXING SETTINGS
P.MIX Programmable Mixer INH • ON Master Channel ___ Slave Channel ___ Rate – __ %
W.MIX Wing Mixer Type INH • ON FP(flaperon) • v(v-tail) • FPv(flaperon + v-tail) • EL(elevon)
