747936
125
Zoom out
Zoom in
Previous page
1/163
Next page
When using in races in which the lead angle setting function is inhibited by the ESC, set "Lead
angle use" to "INH". The "Lead angle use" setting has priority over "Turbo mode". If "Lead angle
use" is set to "INH", the lead angle setting function can be turned off even if "Turbo mode" is set to
"Turbo1" or "Turbo2".
The MC940,960CR shows that the lead angle setting function is OFF ("0" timing) by blinking a LED.
The "Lead angle" and "Point A, B, C, D, E Lead angle" relationship is shown on the graphs below. Graph
[1] shows the relationship when the same value is set at "Points A, B, C, D, E Lead angle" of [1] and [2]
and the "Lead angle" was set to "0" and graph [2] shows the relationship when a value other than "0" was
set at "Lead angle". As shown in the graphs, [2] is added to the "Points A, B, C, D, E Lead angle" set lead
angle and [1] is added to the "Lead angle" set lead angle. For example, if "3" is set at Point A and "Lead
angle" of [2] is set to "2", the actual Point A becomes 3+2=5 (deg). Since "Lead angle" of [A] is "0", the
actual Point A also becomes 3+0=3 (deg).
A B C D E
A
B
C
D
E
1 (Lead angle ="0") Lead Angle(deg)
rpm
Turn on "Lead angle use"
A B C D E
A
基準進角
B
C
D
E
2 (Lead angle >"0") Lead Angle(deg)
rpm
Lead
angle
125
Function
MC Link Function (ESC Link)
Lead angle use
MC940,960CR :ACT/INH
Same as Link software Lead Angle Use.
This function is effective when Turbo Mode is Turbo1 or Turbo2 and sets
whether or not lead angle is used. This setting has priority over the Turbo
Mode setting. When using in races in which the lead angle function is inhib-
ited by the ESC set this function to INH.
INH : Lead angle function not used.
ACT : Lead angle used
Lead angle
MC940,960CR :0deg~59deg
Same as Link software Lead Angle.
When "Lead Angle Use" is turned on the motor lead angle can be set at the
MC960CR. The lead angle can be set up to 59 degrees in 1 degree incre-
ments.
Point A,B,C,D,E Lead angle
MC940,960CR :0deg~59deg
Same as Link software Boost Angle.
Point A,B,C,D,E Rotation
MC940,960CR :0rpm~99990rpm
Same as Link software Boost Angle rpm.
When "Lead Angle Use" is turned on the lead angle versus motor speed of the 5 points A to E can be set. The lead
angle can be set up to 59 degrees in 1 degree increments.
125


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 4PX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 4PX in the language / languages: English as an attachment in your email.

The manual is 10,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info