747936
91
Zoom out
Zoom in
Previous page
1/163
Next page
Adjustment buttons
- Use the (+) and (-) buttons to
make adjustments.
- Return to the initial value by
pressing the (+) and (-) buttons
simultaneously (approx. 1 sec).
Drive ratio
Front 0%:Rear 100%
~ Front 100%:Rear 0%
Initial value:
Front 100%:Rear10 0%
Setting buttons
- Use the (+) and (-) buttons to
make adjustments.
MIX mode
OFF, ON
Initial value: OFF
Trim mode
OFF, ON
Initial value: OFF
91
Function
DUAL ESC Mixing
Use a 50:50 trigger ratio setting. (P66)
Trigger ratio Setting
(Preparation)
- This function has 2 methods. One method is used by switching the drive type (4WD/front/
rear) by one digital trim/dial. The other method performs switching by assigning a switch to
each mode (4WD/front/rear). Both methods are set from among DL1 and DT~1DT6 by dial
select function. (P101)
Dual ESC mixing adjustment
2
(Drive ratio adjustment)
Adjust the front and rear motor controller operation amount
by (+) or (-) button.
The (+) button increases and the (-) button decreases the
rear ratio.
Both the front and rear ratios become 100%
3
(Mix mode setting)
Operate the (JOG) button up and down and select the setting
item "MIX mode". Set the mix mode with the (+) or (-) button.
"OFF" :The EXP function of the 2nd CH and other settings are not mixed.
"ON" :The EXP function of the 2nd CH and other settings are mixed.
4
(Trim mode setup)
Select the "Trim mode" by (JOG) button up, down, left, or
right operation, and use the (+) or (-) button to select the
mixing mode.
"OFF" :Trim of the 2nd CH is added.
"ON" :Trim of the 2nd CH is removed.
The dial select function can control the drive ratio with digital dial or digital trim.(p.101)
Dial / Trim Setting
As this function drives 2 separate motor controllers simultaneously, a mutual load is ap-
plied. Use this function carefully so that the motor controllers are not damaged.
Futaba will not be responsible for motor controller, motor, and other vehicle trouble due
to use of this function.
Note:
1
(Dual ESC setting)
Refer to the left page and set the function to ON and set the
mixing channel.
When switching by one digital trim is set, the set switch per-
forms switching as shown below.
Front drive 4WD Rear drive
5
When finished with setting, return to the Mixing menu screen by pressing the (END) button.
91


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 4PX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 4PX in the language / languages: English as an attachment in your email.

The manual is 10,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info