29035
14
Zoom out
Zoom in
Previous page
1/19
Next page
12
Assembly / Adjustment
Digital Proportional Adjustment
*When making these settings adjustments , do so with the motor disconnected
or the engine not running.
Servo Horn Installation Instructions.
1Connect the receiver, servos, and other components and
then turn on the power switches to transmitter and re-
ceiver.
2Be sure the Steering trim and Throttle trim on the transmitter
are at their neutral position .
3At this time install the servo horn in the manner
described in the instruction manual provided
with the model this system will be used in.
Both servos will move to the neutral
position.
Reversing The Servo Operation Direction
Should the servo operate in the opposite direction re-
quired for your application, reverse the rotation with the
reversing switch.
E.S.C. MC210CB / MC310CB
(Preparations)
1Set the servo reversing switch on the transmitter to normal
side.
2Turn the high point trim fully clockwise.
(Neutral Adjustment)
3Have the throttle trigger at neutral.
4Set the neutral trim to the point where the monitor lamp goes
off.
*The point where the monitor lamp changes from a rapid flashing
light to off is the neutral point.
(High Point Adjustment)
5Hold the throttle trigger in the position just before full throttle.
6Set the high point trim at the point where the monitor
lamp changes from a flashing light to steady light.
*The point where the monitor lamp
changes from a rapid flashing state to
a steady light is the high point.
* Adjust the Amp with the mini
screwdriver supplied with this sys-
tem.
*(forcing the adjustment trims past
their stop will cause internal damage
to the speed control.)
(Monitor Lamp Display)
Neutral Point High Point
Back Side Forward Side
Slow Flashing Off Rapid Flashing ON
ST.
N
R
N
R
SERVO
REV SW
TH.
(Reversing Switches)
Throttle
N Side: Normal
R Side: Reverse
Steering
N Side: Normal
R Side: Reverse
MC210CB
Fully Clockwise
MC210CB
The point where the monitor
lamp changes from a rapid
flashing light to off is the
neutral point.
MC210CB
The point where the monitor
lamp changes from a rapid
flashing state to a steady light
is the high point.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 2PEKA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 2PEKA in the language / languages: English as an attachment in your email.

The manual is 0,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info