747923
18
Zoom out
Zoom in
Previous page
1/30
Next page
19
Assembly / Adjustment
Assembly Precautions
WARNING
Check the receiver, servos, and batter y connectors, to be sure they are fir mly connected.
If a connector is not fully inser ted, vibration may cause the connector to work loose while the model
is operating. This will result in loss of control.
Operate each servo horn over its full stroke and check to see that the linkage does not bind or is not
too loose.
Excessive force applied to the ser vo horn by binding or poor installation may lead to ser vo problems
and result in loss of control.
(Electric Cars and Boats)
Isolate the receiver from vibration by attaching to the chassis or mounting plate with thick double
sided tape.
(Gas Powered Cars and Boats)
Isolate the receiver from vibration by wrapping it in foam rubber or similar type cushioning material.
Protect the unit from water damage by placing it in a plastic bag or waterproof radio box.
The receiver contains precision electronic parts. These par ts are vulnerable to vibration and shock.
Any contact with moisture (water or condensation) may cause receiver malfunction and loss of con-
trol.
Use the ser vo horn screw.
When the ser vo horn comes off, it becomes loss of control.
Keep all devices that emit high frequency noise, such as motors, batteries, and wiring that handles
heavy current loads, at least 1/2 inch away from the receiver and the receiver antenna.
High frequency noise will cause a decrease in operating range and could cause loss of control.
Install electronic speed control heat sinks as well as other components that conduct electricity so they
can not come in contact with aluminum, carbon fiber or other materials that conduct electricity.
If, for example, the speed control came loose while the model was running and touched an aluminum
chassis, a short circuit may occur that would cause irreparable damage to the system as well as loss
of control.
Noise suppression capacitors should be installed on almost all motors.
If the proper capacitors are not installed, high frequency noise will reduce range and cause loss of
control along with various other problems.
Inspect all linkage installations and any point where metal could come in contact with other metal
par ts. Make sure these parts do not touch other metal par ts under vibration.
Should a linkage or other metal par ts come in contact with other metal par ts under vibration, the high
frequency noise generated by this contact will cause interference and possible loss of control.
CAUTION
Do Not disassemble any par t of this system that is not specified in the instruction manual.
Futaba will not be responsible for any damage due to improper disassembly of any par t of the radio
control system.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 2HR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 2HR in the language / languages: English as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info