29031
118
Zoom out
Zoom in
Previous page
1/127
Next page
PIT to RUD mixing (Revolution mixing)
Use this mixing when you want to suppress the
reaction torque generated by main rotor pitch and
speed changes at pitch operation. Adjust so that the
nose does not move in the rudder direction.
An acceleration function which temporarily
increases the correction rate at throttle stick
acceleration/deceleration operation can be set. The
mixing rate at acceleration/deceleration can be set.
Return to Model Menu
Touch the [PIT to RUD] button in the Model
Menu to call the setup screen shown below.
Setting method
When using this function, touch the [INH] button
and display [ON] or [OFF].
When you want to set the same contents at other
conditions, select the group mode (Gr.). When
you want to set the selected condition only, select
the single mode (Sngl).
A mixing curve is set.
<Normal condition mixing curve>
The mixing curve rate starts from a small
value.
For a rotor with a clockwise operation
direction (polarity), when pitch was
operated at the plus side, set so that mixing
is in the clockwise direction. First, trim at
hovering and then adjust the neutral
position.
1. Adjustment between slow and hovering
Repeatedly hover from take off and land
from hovering at a constant rate matched
to your own rhythm, and adjust the pitch so
the nose does not de ect when the throttle
is raised and lowered.
2. Throttle high side (up to climbing from
hovering and diving hovering)
*Repeat climbing and diving from hovering at a constant
rate matched to your own rhythm and adjust the pitch so
that the nose does not deflect when the throttle is raised
and lowered.
Normally, use [Line] type.
However, when a GY Series or other heading
hold gyro is used, since correction is performed by
the gyro, this mixing is not used. If this function is
used when the gyro operation mode is the AVCS
mode, the neutral position will change.
<Idle up condition mixing curve>
Set the mixing rate so that the rudder direction at
high-speed ight is straight ahead. Adjust for each
condition used.
<Acceleration function setting>
Acceleration operation can be performed
for both setting at acceleration (High) and
setting at deceleration (Low).
Acceleration rate setting (Rate)
The return time after operation (Dump.) can
be set.
An operation point (Operation Point) at
acceleration and deceleration can be set
independently. When an operation point
was exceeded, acceleration operation is
performed.
118
<Model Menu (Helicopter Functions)>
118


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 14MZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 14MZ in the language / languages: English as an attachment in your email.

The manual is 21,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info