29031
75
Zoom out
Zoom in
Previous page
1/127
Next page
Return to Model Menu
Touch the [AFR (D/R)] button in the Model Menu to call
the setup screen shown below.
AFR (D/R)
The rudder angle and curve of each operation function can be set. A D/R curve
which can be switched by switch, etc. can also be added. [All model types]
AFR function is used to adjust the throw and
operation curve of the stick, lever, and switch
functions (CH1 to CH12, and V1 to V4) for each
flight condition. This is normally used after End
Point (ATV) has defined the maximum throw
directions (End Point acts on ALL ight condition
settings). When mixing is applied from one channel
to another channel, both channels can be adjusted
at the same time by adjusting the operation rate
through the AFR function.
Setting method
Operation curve adjustment: Six types of
curves (linear, EXP1, EXP2, VTR, line and
spline) can be selected. A maximum 17
points curve can be used for the line and
spline curve types. (Initial setting: 9 points)
The number of points can also be increased
and decreased and curves from complex
curves to simple curves can be used.
Operation speed adjustment: The operation
speed of each function when the function
is operated (including at flight condition
switching) can be adjusted. The function
operates smoothly at a constant speed
corresponding to the set speed.
(Currently selected condition name)
(Currently selected rate name: AFR, D/R1~6)
Function selection
1. When the function select button is touched, a selection screen appears.
2. Select the function you want to set at the selection screen.
(Total number of AFR
and D/R curves set at
the currently selected
condition)
Servo speed setting
(For a description of the setting method,
see the description at the back of this
manual.)
D/R function setting
Screen mode switching
When setting the D/R function, the screen
display mode can be changed. Each time the
button is touched, the mode is switched.
*[Sngl](initial setting): Only the currently
operating curve is displayed.
*The AFR and D/R curves set at the currently
operating condition are displayed.
*[All Cond.]: The AFR curve set at all
conditions is displayed.
Group/single mode switch (Gr./Sngl)
(For more information, see the description at the back of this manual.)
Operation curve setting
(For a description of the setting method, see the description at the
back of this manual.)
75
<Model Menu (Common Functions)>
75


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 14MZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 14MZ in the language / languages: English as an attachment in your email.

The manual is 21,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info