29031
58
Zoom out
Zoom in
Previous page
1/127
Next page
Frequency setting
The T14MZ transmitter uses a synthesizer
system. Its frequency can be changed within the
range of the frequency band of the module used.
The frequency of the R5014DPS receiver is set
from the transmitter. Use a receiver matched to the
frequency band of the transmitter.
Receiver ID code
When the R5014DPS receiver (PCM-G3
receiver) is used, the ID code located on the back
of the receiver case must be entered.
*When two receivers are used with a large model, etc., enter
the 2nd receiver ID also.
Return to Linkage Menu
Touch the [Frequency] button in the Linkage
Menu to call the setup screen shown below.
Frequency
Frequency Band (frequency) setting, modulation mode setting, receiver ID code
setting.
Frequency switching method
For a description of the frequency switching and
ID setting methods, refer to the procedure given in
the Basic Operation section.
Modulation mode change
1. Touch the Modulation Mode button to call
the selection screen, and then touch the
button of the type of modulation used.
2. Touch the [Enter] button to switch the mode.
*When switching from the PCM-G3 mode to another mode,
the mode cannot be switched if the number of channels is
insuf cient due to the wing type used.
3. After switching the modulation mode, turn
the transmitter power off and then switch the
mode by turning the transmitter power back
on.
Modulation mode selection
With the T14MZ, 3 modulation modes (PCM-G3/
PCM1024/PPM (FM)) can be selected. Select the
modulation mode matched to the type of receiver
used.
*After changing the modulation mode, switch the modulation
mode by turning the transmitter power off and on.
Receiver ID code input
1. Touch the receiver ID No. on the screen. The
receiver ID setup screen is displayed. Input
the 8-digit ID number displayed on the back
case of the receiver.
2. If the ID number is correct, touch the [Enter]
button. To correct the number, use the [BS]
button and change the number to the
correct ID code.
*Once the ID code is set, it does not have to be set again as
long as the receiver is not changed.
WARNING
When ying after frequency change, emit radio
waves only after verifying the frequency.
*Also change the frequency clip. Emitting radio waves with-
out veri cation is extremely dangerous.
58
<Linkage Menu>
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 14MZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 14MZ in the language / languages: English as an attachment in your email.

The manual is 21,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info