29029
23
Zoom out
Zoom in
Previous page
1/127
Next page
23
<Basic Operation>
How to turn ON/OFF the power of the
transmitter
For safety reasons, the radio will be emmiting
only after confirming when turning on the power.
Please follow the instructions for turning on/off the
transmitter.
When turning on the power of the transmitter
1. Turn on the power switch of the transmitter.
*After initialization of the transmitter is over, the frequency
confirmation screen pops up, and LED monitor turns on
pink.
2. Check the frequency shown on the screen. If
it is OK, then select [YES] and push the enter
button.
*LED monitor turns to green and the transmitter begins to
emit radio waves.
*To not transmit, select [NO] and push enter button.
Then, you will see the home screen and you
will be able to set conditions.
How to stop the transmitter
Turn off the power switch of the transmitter. The
internal circuit of the transmitter starts the shut
down process including saving the set-up data. The
LED will blink yellow while the transmitter is in
the shutdown process.
Warning
Once you turn off the power, never operate the
power switch until the power shutdown process
is fully completed. If you turn on the power
switch again while the transmitter is still in the
process of power shutdown, the transmitter
power does not start.
How to change the frequency/How to set ID
The T12Z system has employed the frequency
synthesizer scheme. The T12Z transmitter will set
the frequency of the R5014DPS (PCMG3 receiver)
by the wireless data transmission. When you are
using a new PCMG3 receiver and changing the
frequency, set ID or frequency using the following
instructions.
In case of using PCMG3 receivers
*Make sure that PCM-G3 is set as a modulation scheme.
Then change the frequency by the following instruction.
How to change the frequency
7XUQRQWKHWUDQVPLWWHUSRZHU$FRQÀUPDWLRQ
message ("TRANSMIT?") is displayed. Since
you do not want to transmit, select [NO] and
then push the enter button.
2. Select the area that displays the frequency
on the home screen or in the linkage menu
and push the enter button.
*The frequency setup screen appears.
﷈ﶰ﷊ﶲﶪ﷊ﶸ﷎ﶢ
ﴶﴸﴸﳜ
﷐﷒ﶸ﷌ﶸﶶﵾﶈ﷈ﶰ﷊ﶲﵾ﷎ﷄﶆﶞ
dXﻨXbﻞd`f:D＀ﻦ
Xb:D＀
ﶺﶶ﷌ﶪﶼ﷒ﶬﷂﶶﶸﵺﵺﵺﵺﵺﵺﵺ
ﶰ﷊﷎﷊ﷂﶨ﷊ﶰﷂ﷌ﵺﵺﵺﵺﵺﵺ
﷈ﶰ﷊ﶲﵾ﷐﷒ﶸ﷌ﶞﵼ﷒ﶰ﷊﷒
﷢ﶸ﷌ﶰ﷊﷎﷊ﷂﶨ﷊ﶰﷂ﷌ﵺﵺ
@R4R8
4N:F`
ffffdffd
86*.J
ﶺﶶ﷌﷊ﶼ﷤
﷎ﶶﶸ﷌ﷂﶬ﷤
ﴶﴸﳰﴶﴸﳰﴸﴸ
3. Select [RECEIVER ID] and push the enter
button.
*The receiver ID code input screen appears.
4. Input the 8-digit ID code stuck to the receiver
case. If the inputted ID code is correct, select
[ENTER] and then push the enter button.
6HOHFWWKH¿JXUHZLWKWKHFXUVRUNH\DQGSXVKWKHHQWHUNH\
for each digit.
*Use [BACK SPACE] to move back digit by digit for
correction if you made a mistake. When you want to stop
ID code change, push the return key to return to the original
screen.
*Once the receiver ID code is set, it does not have to be reset
as long as the receiver is not changed.
*When you use two receivers with a large aircraft, input the
ID of each receiver.
5. When switching the frequency, select [BAND
NO.] and push the enter button.
*The frequencies which can be selected appear on the screen.
6. Select the frequency you want to use and
push the enter button.
$FRQ¿UPDWLRQPHVVDJHDSSHDUV
*When changing the frequency band, change the module
before turning on the power.
7. If the frequency is correct, push the enter
button.
*A screen which shows that frequency data is being sent
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 12Z at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 12Z in the language / languages: English as an attachment in your email.

The manual is 4,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info