168716

Fusion pp am200010 Manual

6
Zoom out
Zoom in
Previous page
1/9
Next page
1010
11
1 2 3
4
5
9
12
11
876 10
1. Speaker Output Connections
Ensure that the speakers are connected observing correct polarity.
2. Fuses
Ensure fuses are replaced with the same type and rating (PP-AM100010 Pictured Above).
PP-AM100010 25A x 3
PP-AM200010 40A x 3
PP-AM300010 40A x 4
3. Power
FUSION amplifiers should be connected directly to the 12V battery terminal with an inline fuse or
circuit breaker as close to the battery as possible.
Ground
When grounding/earthing your amplifier ensure that the location is a good source of ground
(preferably the floor pan). Make sure the metal is clean of paint etc, as a poor earth could
damage your audio system.
Remote Turn On
This connection turns the amplifier on and should be connected to the remote turn on lead from
the Head Unit. If one is not available a switched 12V source must be used.
4. Output Connectors
Line level output for connection to an additional amplifier
5. Input Connectors
Choose the correct length RCA interconnects and run them to the RCA outputs of the source
unit. Avoid running beside other looms and or power cable.
6. Input Level
This control is used to match the input level of the amplifier to the output level of your head unit
1. Turn the amplifier level to zero.
2. Turn the volume of the head unit to ¾ and the bass and treble to zero.
3. Adjust the level control until the desired maximum volume is achieved without distortion.
4. Failure to follow these steps may cause permanent damage to the audio system.
7. Frequency Control
12dB/Octave Low Pass crossover, variable from 32Hz to 320Hz.
8. Subsonic Filter
This is a variable control that filters out all sub bass frequencies below the set point at 12dB/
Octave.
9. Boost Control ( Rear )
Adjust the Bass Boost to the desired level
10. Remote Level Control
Connect the Remote Level Controller using the supplied cable.
11. Power ON LED
Amplifier is operational when illuminated.
12. Protection LED
When illuminated the amplifier is in protection mode due to any of the following fault conditions.
Short Circuit, Thermal, Output Short, DC Offset.
MONOBLOCK AMPLIFIERS
PP-AM100010, PP-AM200010, PP-AM300010
Downloaded from www.Manualslib.com manuals search engine
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fusion pp am200010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fusion pp am200010 in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info