Manual Fusion pp am 9002 (page 18 of 21) (English)

166162

Zoom out

Zoom in

1/21

SPEAKER LOAD

Keep in mind FUSION PowerPlant Ampliﬁer series are high power ampliﬁers and not high

current ampliﬁers. In other words, they require a minimum impedance of 2 ohms STEREO and

4 ohms bridged MONO to operate trouble free. Too low of impedance could send your FUSION

ampliﬁer into protection mode and/or damage the ampliﬁer.

SPEAKER WIRING

Choose the correct speaker wire for your application. Most applications will require a minimum

of 16 gauge. Route the speaker wire taking the same precautions you took when you ran the

power cables. Terminate these wires at the speaker end by using insulated speaker terminals

(not supplied) or by soldering the connection. Make sure the speaker connections are positive to

positive and negative to negative. At the ampliﬁer end, use a Hex type screwdriver to loosen the

speaker terminals on the ampliﬁer. Connect the speaker wires and tighten the screws securely.

Check to make sure you’ve maintained proper polarity and balance.

SPEAKER TERMINAL BLOCK

REMOTE TURN-ON

This terminal must be connected to a switched +12V source. Typically, remote turn-on leads

are provided at the headunit which will turn the ampliﬁer on and off in correspondence with the

source. If the head unit does not have a remote turn-on lead, then a power antenna wire can be

used. If neither of these leads are present on the head unit then a switched +12V supply must

be used, like the ACC +12V.

Run a minimum of 18 gauge wire from the ampliﬁer location to the source of the switched +12V

lead. If possible, route this wire on the same side of the vehicle as your power cable. Connect the

source remote output to the wire. Go back to the ampliﬁer and cut the wire to length. Loosen the

screw terminal marked REM on the ampliﬁer using a Hex Phillips type screwdriver. Slip the wire

into the connector and tighten the screw securely.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fusion pp am 9002 in the language / languages: English as an attachment in your email.

The manual is 2,96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fusion pp am 9002 Manual

Product: