Manual Fusion nv am 20004 (page 13 of 23) (English)

166878

Zoom out

Zoom in

1/23

CONNECTION

Note: Ensure the audio system is off during the installation of FUSION product. Once the

installation is complete FUSION recommends that you turn the volume of the source unit up

slowly so not to damage the speakers. Please recheck the complete installation prior to turning

the audio system on.

POWER

FUSION ampliﬁers should be wired directly to the vehicle battery using appropriately sized

cable. Start at the vehicle battery and run the power cable through to the ampliﬁer. FUSION

recommends the use of grommets when passing the power cable through any metal wall. Avoid

sharp corners or sharp body parts that may easily cut through the insulation on the cable.

Avoid running the power cable over engine components or near heater cores. The use of an

inline fuse or circuit breaker is essential. This will prevent the risk of a potential ﬁre caused by

a short circuit in your power cable. Connect the fuse holder or circuit breaker as close to the

battery positive terminal as possible. Use a fuse or circuit breaker of equal value as that found

on the chassis of your FUSION ampliﬁer. You may now connect the cable to the battery, but

remember to leave the fuse out or circuit breaker off until all other cable connections are made.

GROUND

When grounding your FUSION Ampliﬁer locate a metal area close to the ampliﬁer that is a good

source of ground (preferably the ﬂoor pan). Once again, investigate the area you wish to use for

electrical wires, vacuum lines, and brake or fuel lines. Use either a wire brush or sandpaper to

eliminate unwanted paint. This will allow a better contact for your ground. Use the same gauge

cable for the ground as you did for the power. Secure the ground cable to the body using a bolt,

star washer and nut. Spread silicon over the screw and bare metal to prevent rust and possible

water leaks. Now it’s time to connect the power and ground cables to the ampliﬁer. Cut both

cables to length. Loosen the +12V and the GND connections on the ampliﬁer. Terminate the

ground ﬁrst, and then the +12V. Make sure that you terminate them into the correct terminals.

Now tighten the screws down securely.

POWER TERMINAL BLOCK

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fusion nv am 20004 in the language / languages: English as an attachment in your email.

The manual is 4,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fusion nv am 20004 Manual

Product: