522165
4
Zoom out
Zoom in
Previous page
1/5
Next page
PUBLISHED BY FUSION ELECTRONICS LIMITED:
© Copyright 2010 by FUSION Electronics Limited.
All rights reserved. Specications and design are subject to change
without notice.
YOU CAN HELP PROTECT THE ENVIRONMENT!
Please remember to respect the local regulations:
Hand in the non-working electrical equipment
to an appropriate waste disposal center.
006
INSTALLATION
007
TROUBLE SHOOTING
INSTALLATION GUIDE
1. Check mounting position for adequate space (see caution)
2. Place the mounting bracket in position, then mark and drill the mounting holes.
3. Place the mounting bracket and insert screws.
4. Connect the wires from the source unit to the box speaker ensuring the correct polarity is
observed.
5. Attach the box speaker to the bracket using the mounting knobs supplied
6. Adjust the angle of the speaker to the preferred position before tightening the mounting knobs
CAUTION: For speaker mounting restrictions, please refer to manufacturers recommendations for any
related navigational equipment.
Installation Tips
Any speaker will only perform to its best capabilities, when correctly placed in the listening area.
FUSION Engineers recognise that unlike a home or motor vehicle installation, there are an extremely
wide range of marine environments where speakers may be placed. FUSION Full Range Marine Speakers
are optimised to perform in the widest possible range of mounting locations, but a little thought and
care with placement will always be rewarded with better sound.
High frequencies are directional. Placing the speakers low down in the boat will lose some of this
information.
Speakers should be placed to simulate a “sound stage”, by being placed where you are able to hear
both speakers in a stereo situation.
TROUBLE SHOOTING
Before you contact your FUSION dealer or service centre, FUSION requires that you do some simple
trouble shooting to help diagnose the problem.
Problem Solution
No sound Check all connections from the source unit amplier to
the speaker terminals are connected correctly
System lacks in bass Check the connections from the source unit/
amplier to the speaker. Ensure the positive wire from
the source is connected to the positive of the speaker.
System lacks in high frequencies Check polarity
Check the bass / treble control settings on the source
unit
Distorted sound Check all wiring
Check that it is not the surrounding panels of the craft
rattling. Check connections from the source to the
speaker.
www.busse-yachtshop.de | info@busse-yachtshop.de
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fusion MS-BX402 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fusion MS-BX402 in the language / languages: English as an attachment in your email.

The manual is 1,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info