167627

Fusion en am 8001 Manual

21
Zoom out
Zoom in
Previous page
1/40
Next page
2121
4 HIGH PASS:
Set the crossover switch 2 to HP and turn this control to 65Hz or above when using speakers smaller than
6 x 9”. This feature is designed to filter out all low bass frequencies that only subwoofers should produce.
Note: Failure to do so could result in speaker damage.
5 LEVEL:
This allows level adjustment of the input signal. Use this control to correctly match the head unit to the
amplifier. To set this control correctly, turn the amplifier level to MIN and the head unit to 3/4 volume, with
the bass and treble on zero, then slowly turn up this amplifier level control towards the MAX end of the
control. Note: If the sound becomes distorted, turn this control down.
6 RCA INPUT:
Connect these RCA connectors to a head unit with a low level output connection.
7 RCA OUTPUT:
Use these RCA output connectors to connect to a secondary amplifier. This output is a pass-thru
connection derived from the RCA input connector so the signal level and frequency response is the same as
the original input signal.
8 GROUND INPUT:
Connect directly to the vehicle’s chassis via a 8 gauge power cable.
Note: This is to be the first wire to connect when wiring up an amplifier ,damage could result if this is
not done.
9 REMOTE INPUT:
This terminal is for turning the amplifier on and off. This requires a switched positive (+12V) to power ‘ON’
the amplifier, this can be found on the rear of the head unit in the form of a electric antenna output, or a
remote on output. If not available you can wire to the ACC position on the key.
10 +12V INPUT:
This must be connected to the vehicle battery positive (+) terminal via an 8 gauge power cable and with an
inline fuse or circuit breaker at the battery end.
Note: This is the last wire to connect up during installation as damage could result.
11 FUSES:
Please ensure correct type of fuse is fitted, as specified in this manual.
Note: EN-AM3002 has 1 x 25A fuse, EN-AM4502 has 1 x 35A fuse.
12 SPEAKER OUTPUT:
See 2/1 channel installation diagrams on page 28 for correct speaker connection.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fusion en am 8001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fusion en am 8001 in the language / languages: English as an attachment in your email.

The manual is 3,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info