Manual Fusion en am 6004 (page 25 of 40) (English)

167626

Zoom out

Zoom in

1/40

2525

6 CROSSOVER SELECTOR:

Set the appropriate mode of operation. The two positions available are OFF and HP (front channel).

See points 5 and 7.

7 LEVEL:

This allows level adjustment of the input signal. Use this control to correctly match the head unit to the

ampliﬁer. To set this control correctly, turn the ampliﬁer level to MIN and the head unit to 3/4 volume, with

the bass and treble on zero, then slowly turn up this ampliﬁer level control towards the MAX end of the

control. Note: If the sound becomes distorted, turn this control down.

8 HIGH PASS:

Set the crossover switch 9 to HP and turn this control to 40Hz or above when using speakers smaller than

6 x 9”. This feature is designed to ﬁlter out all low bass frequencies that only subwoofers should produce.

Note: Failure to do so could result in speaker damage.

9 CROSSOVER SELECTOR:

Set the appropriate mode of operation. The two positions available are OFF and HP (rear channels). See

points 8 and 10.

10 LEVEL:

This allows level adjustment of the input signal. Use this control to correctly match the head unit to the

ampliﬁer. To set this control correctly, turn the ampliﬁer level to MIN and the head unit to 3/4 volume, with

the bass and treble on zero, then slowly turn up this ampliﬁer level control towards the MAX end of the

control. Note: If the sound becomes distorted, turn this control down.

11 SUBWOOFER RCA INPUT:

Connect these RCA connectors to the rear or subwoofer low level output connection from the headunit.

12 REAR RCA INPUT:

Connect these RCA connectors to the rear low level output connection from the headunit.

13 FRONT RCA INPUT:

Connect these RCA connectors to the front low level output connection from the headunit.

14 GROUND INPUT:

Connect directly to the vehicle’s chassis via an 8 gauge power cable.

Note: This is the ﬁrst wire to connect when wiring up a ampliﬁers, damage could result if this is not done.

15 REMOTE INPUT:

This terminal is for turning the ampliﬁer on and off. The remote input requires a switched positive (+12V)

to power ‘ON’ the ampliﬁer, this can be found on the rear of the head unit in the form of a electric antenna

output, or a remote on output. If not available you can wire to the ACC position on the key.

16 +12V INPUT:

Connect directly to the vehicle battery positive (+) terminal via an 8 gauge power cable, with an inline fuse

or circuit breaker at the battery end.

Note: This is the last wire to connect up during installation, damage could result if this is not done.

17 FUSES:

Please ensure the correct type of fuse is ﬁtted, as speciﬁed in this manual.

Note: the EN-AM10005 has 3 x 25A fuse.

18 SPEAKER OUTPUT:

See 5/3 channel installation diagrams on page 33 for correct speaker connection.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fusion en am 6004 in the language / languages: English as an attachment in your email.

The manual is 3,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fusion en am 6004 Manual

Product: