691368
9
Zoom out
Zoom in
Previous page
1/12
Next page
WI-FI CLIENT: Configures the zone stereo as the wireless
client, allowing it to wirelessly connect to other devices.
WI-FI ACCESS POINT: Configures the zone stereo as the
wireless access point (Wireless Access Point Settings,
page 5).
ADVANCED: Allows you to set the advanced wireless and wired
settings, such as DHCP and SSID.
RESET: Resets all network settings for this stereo to the factory
default values.
Advanced Network Configuration
You can perform advanced networking tasks on a FUSION
PartyBus device, such as defining DHCP ranges and setting
static IP addresses.
Wireless Access Point Settings
Select > SETTINGS > NETWORK > ADVANCED > WI-FI
ACCESS POINT.
NOTE: You must configure the device to be a wireless access
point before you can change the settings (Setting the Apollo
SRX400 Zone Stereo as a Wireless Access Point, page 3).
SSID: Sets the SSID, or name, for the network.
AP SECURITY: Sets the type of wireless security protocol used
by the access point.
NOTE: It is strongly recommended that you set the AP
SECURITY using WPA2 PERSONAL. It is the most widely-
used and secure wireless security protocol.
PASSWORD: Sets the password for the access point. This is
not available when the AP SECURITY setting is set to
NONE.
COUNTRY: Sets the region where the stereo is located.
Different regions may use different channels on the wireless
spectrum, so you should set this to best accommodate local
wireless devices.
CHANNEL: Sets the access point to use a group of channels in
the high, low, or middle range of the available spectrum for
your region. You may experience better performance if you
set the channel in a range with fewer broadcasting access
points.
DHCP SERVER: Sets the device to act as a wireless access
point and the DHCP server on the network.
WPS: Initiates a WiFi Protected Setup (WPS) connection.
Devices with a WPS button or setting can connect to the
access point on this stereo when the WPS connection is
active.
NOTE: It can take up to two minutes to successfully connect
to the access point after you select WPS.
DHCP Settings
Select > SETTINGS > NETWORK > ADVANCED > DHCP
SERVER.
DHCP ENABLED: Sets the device as the DHCP server on the
network.
START IP: Sets the first IP address in the IP-address range of
the DHCP server.
END IP: Sets the final IP address in the IP-address range of the
DHCP server.
Setting a Static IP Address
If the stereo is configured as a DHCP server, it is automatically
assigned the IP address of 192.168.0.1. You can change this IP
address.
If the stereo is a client on the network and you do not want the
DHCP server to automatically assign an IP address to the
stereo, you can set a static IP address.
NOTE: Every device on the network must have a unique IP
address. If you select a static IP address that is the same as the
IP address on the network, the devices will not work properly.
1
Select > SETTINGS > NETWORK > ADVANCED.
2
Select an option:
If the stereo is connected using an Ethernet cable, select
ETHERNET IP > STATIC IP.
If the stereo is set as a wireless access point or wireless
client, select WI-FI STATIC IP.
3
Select an option:
To set the IP address, select IP, and enter the IP address.
To set the subnet mask, select MASK, and enter the
subnet mask.
NOTE: The subnet mask must match all other devices on
the network to work properly. A typical subnet mask is
255.255.255.0.
To set the default gateway IP address, select GATEWAY,
and enter the gateway IP address.
NOTE: The default gateway is typically set as the IP
address of the DHCP server on the network.
4
Select SAVE.
Resetting Network Settings
You can reset all network settings for this stereo to the factory
default values.
Select > SETTINGS > NETWORK > RESET > YES.
Appendix
FUSION-Link Remote Control App
You can use the FUSION-Link remote control app on your
compatible Apple or Android device to adjust the stereo volume,
change the source, control playback, select and manage radio
presets, and adjust some stereo settings.You can use the app to
set up and configure DSP profiles on the stereo.You can use the
app to update the stereo software wirelessly
The app communicates with the stereo using a wireless
connection to the mobile device. You must connect your
compatible device to the stereo using Bluetooth or WiFi
technology to use the app.
If the stereo is connected to a network with a WiFi access point,
the app can communicate with the stereo using the network for
greater range than a Bluetooth connection.
NOTE: You must connect the app using a WiFi connection to
update the stereo software wirelessly. You cannot update device
software using a Bluetooth connection.
For information about the FUSION-Link remote control app for
compatible Apple or Android devices, go to the Apple App Store
or the Google Play store.
Registering Your Apollo SRX400
Help us better support you by completing our online registration
today.
Go to www.fusionentertainment.com.
Keep the original sales receipt, or a photocopy, in a safe
place.
Cleaning the Device
1
Dampen a soft, clean, lint-free cloth with fresh water.
2
Gently wipe the device.
Software Updates
For best results, you should update the software in all FUSION
devices at the time of installation to ensure compatibility.
You can update the software using the FUSION-Link remote
control app on your compatible Apple or Android device. To
Appendix 5
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fusion Apollo MS-SRX400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fusion Apollo MS-SRX400 in the language / languages: English as an attachment in your email.

The manual is 1,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fusion Apollo MS-SRX400

Fusion Apollo MS-SRX400 User Manual - German - 14 pages

Fusion Apollo MS-SRX400 Installation Guide - Dutch - 4 pages

Fusion Apollo MS-SRX400 User Manual - Dutch - 14 pages

Fusion Apollo MS-SRX400 User Manual - French - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info