522215
2
Zoom out
Zoom in
Previous page
1/2
Next page
The processor is position sensitive -
Configuration is required; set [INST MENU] settings accordingly. (See manual; section 1.3)
Antenna Mounting - The antenna must be mounted above all other structures for an unobstructed view.
SC50/110
antenna
required horizontal seperation
1.5 meters 3 meters
10cm mast 30cm mast
Horizontal separation between antenna and structure
must
be: 10 cm =1.5 m, 30 cm =3 m (minimum)
Distance increases for larger obstructions. See diagram
Failure to comply will cause multi-path reflection problems and heading loss (see “check install section”)
Confirming Satellite Status
Check the receiving condition of each antenna unit as follows:
Press the [MENU] key to open the menu, select SATELLITE and press the [ENT] key.
Use or to select between antenna elements to confirm receiving status.
Press the [DISP] key to close the menu.
SC50/110 Operations and Information Quick Guide GP Page 2 3/7/2005
Position status North DOP RX signal level
(
lower is better
)
Bars that extend past first vertical line
are used in the headin
g
calculation
Elevation 5 °
(More accurate)
Antenna element no.
Troubleshooting: No RX signal on antenna 1, 2, or 3.
Switch antenna cable with one of the other known good
antennas to confirm antenna or processor problem
Elevation 45 °
(Less accurate)
Satellites
highlighted in
black used for
calculation
W
A
AS
Checking Installation- multi-path and receive problems (re-confirm after adding any new near-by structures on the vessel)
Maintenance Menu Access - Press and hold [MENU] and [ENT] keys simultaneously (~ 8 sec.), at third beep release
[MENU] key first, then [ENT] key. Access [
ANT MONI] from the maintenance menu and press [ENT].
Multipath Index for the baseline
between antenna 1 and antenna 3
Must
be 1.5 or lower
Multipath Index for the baseline
between antenna 1 and antenna 2
Must
be 1.5 or lower
Circular Graph displays (in 12 directions) tracking
error in relation to the vessel bow. The highest error
and its opposing direction are shown in black
(illustration shows error at 10 and 4 o’clock
position). Note: Two (2) sectors will always be
illuminated even when no heading loss is present
Bar Graph displays tracking error in 12 directions
Longer bars = more error (caused by obstacles)
Sectors opposite to obstacle may have most error
Elapsed time displays accumulated tracking data
(up to 99 hrs 59 mins). Collect a minimum 12 hrs
of data for valid information.
After confirming above information, turn the vessel in a complete circle to check for correct and stable heading
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno SC-110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno SC-110 in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Furuno SC-110

Furuno SC-110 User Manual - English - 89 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info