612625
9
Zoom out
Zoom in
Previous page
1/22
Next page
Page 17 Page 18
Caution: Keep the radio and handset at least 1 meter away from any magnetic
device such as compass on your vessel.
3.7 RECESSED INSTALLATION
1. Tape the installation template onto the chosen location site.
2. Cut out the area marked by the solid dark line. (The dashed line indicates the
total area that will be covered by the radio fascia after installation.)
3. Remove the installation template and slide the radio into the cavity.
4. Working from the rear of the bulkhead, align the racheted outstand on each
side of the radio with the central hole in each mounting bracket.
5. Use the two short M5x10 screws to screw the mounting brackets to the sides
of the radio.
6. Slide two M5x32 screws through the screw hole in the mounting bracket,
then attach the lock nut and the stopper. If your bulkhead exceeds 13mm,
the stopper nut can be discarded if necessary.
7. Tighten the M5x32 screws until the radio is held against the rear of the
bulkhead.
8. Tighten up the lock nuts to secure the installation.
. BASIC OPERATION
4.1 TRANSMISSION AND RECEPTION
CAUTION: Transmitting without an antenna may damage the radio.
1. After the radio has been installed, make sure of the power supply and
antenna being properly connected.
2. To rotate the VOLUME/POWER knob clockwise turn on the radio and select
a comfortable volume level.
3. To turn the SQUELCH knob clockwise until the background noise
disappears.
4. Rotate CH knob to select channel
5. Press Hi/Lo key to select high power or lower power.
6. Press the PTT (Push-To-Talk) button on the handset to make the radio into
transmission mode. TX indicator on LCD is displayed.
7. Speak clearly in a normal voice into the microphone.
8. Once the transmission is finished, release the PTT button. The radio is at
receive mode, icon Rx appear on screen.
4.2 CHANNEL SELECTION
4.2.1 Channel 16 Key gives you a quick access to the channel 16
Channel 16 is the distress and safety channel. It is used for establishing
initial contact with another station and for emergency communications.
Channel 16 is monitored during dual watch. While standing by,
monitoring channel 16 is a must.
4.2.2 INTL MODE
There are all 55 International channels listed in the channel list section.
These channel groups may be specified for the operating area. To select
the desired channel: rotate CHANNEL/SELECT knob to select channel in
the active band. With the knob being rotated, the channel is displayed on
the LCD display;
4.3 MEMORY CHANNELS
4.3.1 Memory Channels selection
1 Press and hold the Hi/Lo/ mem button to enter the MEM mode;
2 At mem mode, rotate CHANNEL/SELECT knob to select MEM
channel in the memory. With the knob being rotated, the
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno RO4700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno RO4700 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info