522191
83
Zoom out
Zoom in
Previous page
1/103
Next page
5. MAINTENANCE, TROUBLESHOOTING
5-3
5.3.2 Processor unit test
This test checks the processor unit for correct operation. Open the diagnostic test op-
tions window, select [PROCESSOR UNIT] then push the Course control knob. The
results for the ROM, RAM and RUDDER ANGLE are shown as OK or NG. If NG ap-
pears, repeat the test. If the error condition continues, contact your dealer.
[ROM]: "OK" for normal, program number
[RAM]: RAM test, "OK" for normal
[BACKUP]: Backup data test, "OK" for normal.
[RUDDER ANGLE]: "OK" for normal, actual rudder angle.
[BYPASS/CLUTCH]: Bypass/clutch amperage. ("NOT PRESENT" shown in case of
no connection.)
[RC1/RC2]: Remote controller state (ON or OFF) and rudder signal input value. "NOT
USED" shown in case of no connection.
[INPUT VOLTAGE]: Voltage.
[PORT1/PORT2/CAN]: I/O test for PORT1/PORT2/CAN (CAN bus). OK for normal.
[CAN ID]: ID of CAN bus equipment.
5.3.3 Control unit test
This test checks the control unit for correct operation. Open the diagnostic test options
window, select [CONTROL UNIT] then push the Course control knob. The results for
[ROM], [RAM], [BACKUP], and [COMMUNICATION] are shown as OK or NG (No
Good). If NG appears, repeat the test. If the error condition continues, contact your
dealer.
ROM: OK 6454007-**.**
6454009-**.**
RAM: OK BACKUP: OK
RUDDER ANGLE: OK 0°
BYPASS/CLUTCH: 0.7A
RC1/RC2: OFF -1° /OFF -2°
INPUT VOLTAGE: 24.5 V
PORT1/PORT2/CAN: - -/- -/OK
CAN ID: 39713 CPU/PWR: */*
PROCESSOR UNIT ID: 39768
*: Version no.
**.**: Program version no.
Not shown with Fantum Feedback
TM
.
For Fantum Feedback
TM
, “FANTUM
FEEDBACK” is displayed.
ROM: OK 6454011-**.**
6454010-**.**
RAM: OK BACKUP: OK
COMMUNICATION: OK
CONTROLLER ID: 2
CAN ID: 0 CPU:*
CONTROL UNIT
*: Version no.
**.**: Program version no.
83


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno NAVpilot-700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno NAVpilot-700 in the language / languages: English as an attachment in your email.

The manual is 7,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Furuno NAVpilot-700

Furuno NAVpilot-700 Installation Guide - English - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info