522136
36
Zoom out
Zoom in
Previous page
1/47
Next page
29
4.4 Inside-hull
Transducer
The thru-hull mount transducer (520-5PSD,
520-5MSD) may also be installed inside the
hull, following the procedure below.
Necessary tools
You will need the following tools:
Sandpaper (#100)
Silicone sealant
Silicone grease
Remarks on installation
Turn off the engine and anchor the boat
while installing the equipment.
Install the transducer in the engine room.
Choosing the mounting location
Keep the following points in mind when
choosing a mounting location:
The mounting location should be where
the hull is of single-hull thickness and is
void of air or flotation materials other than
solid fiberglass between the transducer
face and the water.
Do not place the transducer over hull
struts or ribs which run under the hull.
Avoid a location where the rising angle of
the hull exceeds 15°, to minimize the
effect of the boats rolling.
You will finalize the mounting location
through some trial and error. The
procedure for this is shown later.
50 cm
50 cm
15 cm
15 cm
1/3
1/2
Transducer
mounting
location
Centerline
Inside-hull transducer mounting location
Attaching the transducer
1. Clean the transducer face to remove
any foreign material. Lightly roughen the
transducer face with #100 sandpaper.
Also, roughen the inside of the hull
where the transducer is to be mounted.
2. Warm the silicone sealant to 40°C
before usage to soften it. Coat the
transducer face and mounting location
with silicone sealant.
Transducer
Silicone
Sealant
Coating transducer face
with silicone sealant
3. Press the transducer firmly down on the
hull and gently twist it back and forth to
remove any air which may be trapped in
the silicone sealant.
Checking the installation
1. Connect the battery to the display unit.
2. Turn on the display unit.
3. Press the [MODE] key to choose
SINGLE FREQ.
4. Choose 50 kHz or 200 kHz, and then
press the [MENU/ESC] key to close the
mode menu.
5. Press the [PROG] key to show the
pop-up window for automatic/manual
selection.
6. Press to choose Manual.
7. Press the [MENU/ESC] key..
8. Press the [GAIN] key to set the gain to
“5” and then press the [MENU/ESC] key.
9. Press the [RANGE] key to set the range
to 10 meters (feet) and then press the
[MENU/ESC] key.
www.Busse-Yachtshop.de email: info@busse-yachtshop.de
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno LS-6100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno LS-6100 in the language / languages: English as an attachment in your email.

The manual is 1,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info